Epson Aculaser C1600 User Manual Download Page 69

Page: 69 / 93

Ready
indicator
(green)

Error
indicator
(orange)

Toner
indicator
(orange)

Display of
Remote
Panel
Program

Condition

Action

Off

TONER OUT
X (YMCK)

Toner out

Note:

This message appears
when the

Toner Out

Stop

in the Remote

Panel Program is set to

Off

Replace the toner
cartridge.

Note:

Printing can continue,
however, the printing
results are not
guaranteed.
If printing is continued,
the Error indicator
(orange) lights up and
printing stops.

Slow
blinking

Rapid
Blinking

NON
GENUINE
TONER X
(YMCK)

The installed toner
cartridge is of an
unapproved type.

Install a Epson toner
cartridge of the
appropriate type.

See “About Toner
Cartridges” on page 38.

Slow
blinking

P/U LOW

Photoconductor unit
near end

Prepare the new
photoconductor unit.

T/C
MEMORY
ERROR

Toner cartridge memory
error

Re-install the specified
toner cartridge.

VIDEO I/F
ERROR

Video interface error

Turn off the printer. After
a few seconds, turn on
the printer.

PROCESS
CAUTION-ID
C

Process caution

Open and close the
printer’s covers.

If the error is not
corrected, turn off the
printer. After a few
seconds, turn on the
printer.

AcuLaser C1600 User’s Guide

Troubleshooting

Summary of Contents for Aculaser C1600






























































































Search results

Summary of Contents for Aculaser C1600

Reviews:

Related manuals for Aculaser C1600

Brands by name

Popular brands

Epson Aculaser C1600, User Manual

Search results

Summary of Contents for Aculaser C1600

Reviews:

Related manuals for Aculaser C1600

Brands by name

Popular brands