Epson Aculaser C1600 User Manual Download Page 52

Page: 52 / 93

❏

Always close the printer’s covers gently. Never subject the printer to vibration.

❏

Do not cover the printer immediately after using it. Turn it off and wait until it cools down.

❏

Do not leave the printer’s covers open for any length of time, especially in well-lit places; light may
damage the photoconductor unit.

❏

Do not open the printer during printing.

❏

Do not tap media stacks on the printer.

❏

Do not lubricate or disassemble the printer.

❏

Do not tilt the printer.

❏

Do not touch the electrical contacts, gears, or laser devices. Doing so may damage the printer and
cause the print quality to deteriorate.

❏

Keep media in the output tray at a minimum level. If the media is stocked too high, your printer
may experience media misfeeds and excessive media curl.

❏

Keep the printer level to avoid toner spillage.

❏

When lifting the printer, grasp the areas shown in the figure.

❏

If you get toner on your skin, wash it off with cool water and a mild soap.

AcuLaser C1600 User’s Guide

Maintenance

Summary of Contents for Aculaser C1600






























































































Search results

Summary of Contents for Aculaser C1600

Reviews:

Related manuals for Aculaser C1600

Brands by name

Popular brands

Epson Aculaser C1600, User Manual

Search results

Summary of Contents for Aculaser C1600

Reviews:

Related manuals for Aculaser C1600

Brands by name

Popular brands