Epson ActionLaser 1400 Reference Manual Download Page 56

Page: 56 / 95

Paper

Paper specifications

Note:

Since the

quality of any particular brand or type of paper may be changed by the

manufacturer at any time, EPSON cannot guarantee the use of any particular

brand or type of paper. Always test samples

of paper stock before purchasing large

quantities or

printing large jobs.

Paper types: Plain paper

Special paper

Labels

Envelopes

Transparencies

Colored paper

Paper weight:

Paper size:

Paper:

Envelope:

Plain paper: 16 to 24 lb, 60 to 90 g/m

card stock: 24 to 32 lb, 90 to 120 g/m

(manual feed only)

Type

Letter

Legal

Executive

Monarch

Commercial 10
DL

Size

8.5 x 11 inches

8.5 x 14 inches

7.25 x 10.5 inches

210 mm x 297 mm

176 mm x 250 mm

37/8 x 7 1/2 inches

41/8 x 9 1/2 inches

ll0 mm x 220 mm

162 mm x 229 mm

Caution:

Do not load any size of paper

other than those listed above.

Printable area: 4 mm from paper edge

A-2 Technical Specifications

Summary of Contents for ActionLaser 1400
































































































Search results

Summary of Contents for ActionLaser 1400

Reviews:

Related manuals for ActionLaser 1400

Brands by name

Popular brands

Epson ActionLaser 1400, Reference Manual

Search results

Summary of Contents for ActionLaser 1400

Reviews:

Related manuals for ActionLaser 1400

Brands by name

Popular brands