Epson ActionLaser 1400 Reference Manual Download Page 95

Page: 95 / 95

print quality

optimizing, 3-8-10

problems with, 3-5-8

Printable area, A-2

Printer

cleaning, 3-11-12

controlling from MS-DOS, B-2-8

controlling Windows, 2-2-13

features, 1-2

maintaining, RTF-17-24

monitoring the status, 1-9-11

resetting, 3-2

setting up, RTF-1-15

specifications, A-3-5

system requirements, RTF-1

testing, RTF-12

testing the computer connection,

RTF-13

unpacking, RTF-2

Printer driver, RTF-14

Printer driver settings, 2-4-13

accessing, 2-3

resetting to factory defaults, 3-2

saving as a profile in DOS, B-7

Printer overruns, preventing 2-11

Profiles, B-7

Raster graphics, 2-9

Ready light, 1-10

doesn’t come on, 3-3

Reporter, 1-3, B-7-8

Reset button, RTF-12

Resident fonts, 1-8

Resolution, 1-2,2-12

changing for graphics, 2-9

safety instructions, 7

scanned Images, 2-10

Setup dialog boxes, 2-3

SIMM

installing, D-2-3

specifications, D-2

Status, monitoring, 1-3, 1-9-11

Test page, printing, RTF-12

Toner

adjusting the density, 3-10

cleaning spills, 3-12

conserving, 2-7

problems with smudges, 3-6

Toner cartridge

handling precautions, 6

installing, RTF-3-6

replacing, RTF-17-21

specifications, A-5

Toner density, 2-8

adjusting, 3-10

Toner Saving, 2-7

Toner saving mode, 1-3

Transparencies, 1-8

TrueType fonts

converting to bit images, 2-10-11

downloading, 1-9

resident in printer, 1-8

using printer TrueType fonts, 2-11

Vertical bands, 3-5

Window envelopes, 1-7

IN-3

Summary of Contents for ActionLaser 1400
































































































Search results

Summary of Contents for ActionLaser 1400

Reviews:

Related manuals for ActionLaser 1400

Brands by name

Popular brands

Epson ActionLaser 1400, Reference Manual

Search results

Summary of Contents for ActionLaser 1400

Reviews:

Related manuals for ActionLaser 1400

Brands by name

Popular brands