Epson ActionLaser 1400 Reference Manual Download Page 52

Page: 52 / 95

4. Remove any dirt inside the printer with a soft, clean cloth.

Do not use compressed air.

Be sure to clean the laser scanner window. This window

is located in the lower area of the printer interior,

immediately in front of the orange strip.

5. Reinstall the toner cartridge.

6. Close the front cover.

7. Remove any pages and clean the paper tray with a soft cloth.

Removing spilled toner

If toner spills inside the printer, do not use the printer until you

remove all the spilled toner. Follow these steps:

1. If only a small amount of toner is present, remove the toner

cartridge and carefully wipe out the inside of the printer

with a clean, dry cloth Be sure to clean the laser scanner

window, which is located in the lower area of the printer

interior immediately in front of the orange strip.

3-12 Troubleshooting

Summary of Contents for ActionLaser 1400
































































































Search results

Summary of Contents for ActionLaser 1400

Reviews:

Related manuals for ActionLaser 1400

Brands by name

Popular brands

Epson ActionLaser 1400, Reference Manual

Search results

Summary of Contents for ActionLaser 1400

Reviews:

Related manuals for ActionLaser 1400

Brands by name

Popular brands