manualshive.com logo in svg

Epson ActionLaser 1400, Reference Manual

Share
Download
Epson ActionLaser 1400 Reference Manual Download Page 64

EPSON Control Panel for DOS

If you are not running Microsoft Windows, you can control printer

settings through the EPSON Control Panel for DOS. This 

onscreen 

utility

consists of five screens that allow you to do the following:

Change page setup settings, such as the number of copies,

orientation, and page size.
Select a font, point size, or symbol set.

Control the print quality by specifying the edge smoothing, toner

saving, resolution, and toner density settings.
Control how printer memory is used for page protection.
Turn the power save option on or off and specify how long the

printer is idle before power save mode turns on.

Most of the settings available in the EPSON Control Panel for DOS are

the same as the printer driver settings available for Widows. For a

description of the individual printer settings, see Chapter 2.
Some settings, such as those for page setup and font selection, are also

available through your software program Whenever possible, change

settings in yours software program rather than in the EPSON Control

Panel for DOS. Not only is it more convenient, but the settings in your

software program override settings in the EPSON Control Panel for DOS.

Note:

You cannot 

run 

the EPSON Control Panel for 

DOS from 

Windows.

Installation

1.

Insert the EPSON Control Panel for DOS diskette in a diskette drive.

2.

From a DOS prompt, change to the diskette drive by typing A: or B: as

appropriate. Press Enter.

3.

Type SETUP and press Enter. After a few moments, the initial setup
screen appears.

4.

Read the information on the setup screen. Then press Enter to

continue.

B-2

Controlling Printer Settings from 

MS-DOS

Summary of Contents for ActionLaser 1400
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands