manualshive.com logo in svg

Epson ActionLaser 1400, Reference Manual

Share
Download
Epson ActionLaser 1400 Reference Manual Download Page 29

Accessing Printer Driver Settings in Windows

To access printer driver settings, first choose Print from the

File menu to bring up the Print dialog box. You now need to

select another option Depending on your software program,

you need 

to choose 

the 

Setup, Options, 

or 

Printer 

button

Some programs then prompt you to select the ActionLaser 1400

before the Setup dialog boxes appear.

Printer driver settings are accessible on six Setup dialog boxes.

The first Setup dialog box you see is for Paper settings:

At the top of the dialog box are tabs for each Setup dialog box:

Paper, Green, Graphics, Printer, Fonts, and About. The table on

the next page lists the settings available on each.

To change a printer setting, open the appropriate dialog box by

choosing the tab. Change one or more printer settings and then
choose the 

OK 

button at the bottom of the dialog box. If you

want information about any of the printer settings, look up the

setting in this chapter or choose the 

Help 

button.

Controlling the Printer

2-3

Summary of Contents for ActionLaser 1400
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands