Epple Maschinen PW 30 User Manual Download Page 17 | Manualshive

Page: 17 / 50

background image

Stand 31.07.08, PW 30, PW 30 HV, Profile roll

Page 17 of 50

3 Assembly

The machine is delivered pre

– mounted.

3.1

Delivery volume

After receipt of the delivery you have to check directly of shortfalls. Compare
the scope of delivery with the information at the packing slip.
Check whether the machine has damages in transit.

.

3.2

Transport

Warning!

If the lifting tool is not stable enough it can burst what may cause heavy or deadly
injuries. Please observe the following instructions for the carrier box/ palette:



Rope stops



Weight



Balance point



Prescribed means of transport

Warning!

If the lifting tool is not stable enough it can burst what may cause heavy or deadly
injuries. Check before working with lifting tool whether it is admitted for the load
and undamaged. Observe the effective accident prevention regulations for your
business. Never step under lifted loads for your own safety. See that the load is
fixed correctly.

3.3

Storage

By an improper storage the machine or machine parts can be damaged.
Never store the machine under other environmental conditions than in the
operation manual denoted. The warranty claim declines by improper storage.

«
...
15
16
17
18
19
...
»

Summary of Contents for PW 30



















































Reviews:

No comments

Related manuals for PW 30

Brand: AAON Pages: 36

Brand: Keller Pages: 12

Brand: MacDon Pages: 49

Brand: MacDon Pages: 49

Brand: MacDon Pages: 4

Brand: RBC Bioscience Pages: 24

Brand: S&C Pages: 36

Brand: S&C Pages: 15

Brand: S&C Pages: 16

Brand: S&C Pages: 23

Brand: Labnet Pages: 12

Brand: Zero88 Pages: 26

Brand: HAMOKI Pages: 7

Brand: H&S Pages: 56

MIAMI J ADVANCED

Brand: Össur Pages: 35

Brand: Össur Pages: 38

Brand: Össur Pages: 8

Brand: Össur Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands