manualshive.com logo in svg

epiphan video Standalone VGA Grid, User Manual

The Epiphan Standalone VGA Grid is a cutting-edge hardware device that allows users to connect multiple VGA sources to a single display. You can easily set up and operate this device with the help of our comprehensive User Manual, available for free download on our website. Unlock the full potential of your Epiphan Standalone VGA Grid with our detailed instructions and troubleshooting tips, seamlessly accessible at manualshive.com.

Share
Download
background image

Standalone VGA Grid User Guide
                                     

The admin interface

The admin interface

Standalone VGA Grid is managed from a web interface. This means to perform administrative tasks with 
Standalone VGA Grid you use an internet browser on a PC (or laptop, or tablet) connected to the same local 
Ethernet network.

Connect to the admin interface

If you know the IP address of the system you may type it into the address bar of your web browser.

http://<IP Address of the Standalone VGA Grid>/admin

However if this is the first time you access your system, you likely don't know the IP address, so you can use 
one of the following connection methods:

For networks with DHCP use one of the following procedures:

 

l

Connect via DNS-based service discovery

 

l

Connect via the Epiphan discovery utility

For networks without DHCP, use the following procedure:

 

l

Connect via persistent static IP address

You can also connect to a reduced Operator tablet interface. See 

Connect to the tablet 

interface

.

Connect via DNS-based service discovery

The Standalone VGA Grid uses DNS-based messages to advertise details about itself, including its host name. 
With a compatible utility installed on your computer, you can access the system simply by typing its serial 
number and the suffix “.local” into the address bar of your browser.

To ensure you have compatible software, refer to the following table.

Table 4 

Installing Bonjour Print Services

System

Action Needed

Microsoft Windows

You must install Bonjour Print Services: 

 1.  Use the following URL - 

http://support.apple.com/kb/DL999

  

28

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

LaCie LaCinema Mini HD Connect Datasheet preview
LaCinema Mini HD Connect
Brand: LaCie Pages: 4
SanDisk Sansa SDMX1 1GB Declaration Of Conformity preview
Sansa SDMX1 1GB
Brand: SanDisk Pages: 1
SanDisk Sansa C100 Brochure preview
Sansa C100
Brand: SanDisk Pages: 1
Sandstrom S1DVD12E Quick Start Manual preview
S1DVD12E
Brand: Sandstrom Pages: 4
Sansui SC-2100 Service Manual preview
SC-2100
Brand: Sansui Pages: 16
Clever Little Box Luminis AiO User Manual preview
Luminis AiO
Brand: Clever Little Box Pages: 56
Marantz UD9004 User Manual preview
UD9004
Brand: Marantz Pages: 77
Dish Network Pocketdish AV402E Quick Reference Manual preview
Pocketdish AV402E
Brand: Dish Network Pages: 2
Vizio VBR333 Quick Start Manual preview
VBR333
Brand: Vizio Pages: 16
RGBlink UMS4 plus User Manual preview
UMS4 plus
Brand: RGBlink Pages: 42
LaCie LaCinema Mini HD Connect User Manual preview
LaCinema Mini HD Connect
Brand: LaCie Pages: 74
MAJORITY SCHOLARS SCH-DVD-BLK User Manual preview
SCHOLARS SCH-DVD-BLK
Brand: MAJORITY Pages: 24
National Instruments NI PXI-5600 Getting Started Manual preview
NI PXI-5600
Brand: National Instruments Pages: 53
T+A Elektroakustik DAC 8 DSD User Manual preview
DAC 8 DSD
Brand: T+A Elektroakustik Pages: 60
OSEE IMP5212 User Manual preview
IMP5212
Brand: OSEE Pages: 46
Memorex MMP8575 - 2 GB, Digital Player Specifications preview
MMP8575 - 2 GB, Digital Player
Brand: Memorex Pages: 2
Black Iris For Telecom & Technology ETH-FE1 Data Sheet & User Manual preview
ETH-FE1
Brand: Black Iris For Telecom & Technology Pages: 14
Technics RS-CH700 Service Manual preview
RS-CH700
Brand: Technics Pages: 20

Brands by name

Popular brands

Load more brands