manualshive.com logo in svg

epiphan video Standalone VGA Grid, User Manual

The Epiphan Standalone VGA Grid is a cutting-edge hardware device that allows users to connect multiple VGA sources to a single display. You can easily set up and operate this device with the help of our comprehensive User Manual, available for free download on our website. Unlock the full potential of your Epiphan Standalone VGA Grid with our detailed instructions and troubleshooting tips, seamlessly accessible at manualshive.com.

Share
Download
background image

Standalone VGA Grid User
Guide                                     

Mobile / tablet operator interface

Mobile / tablet operator interface

Epiphan's tablet interface is designed for touch-screen devices. Use your tablet or mobile device to perform 
confidence checks and basic operator tasks such as verifying disk space or starting and stopping recording.

This section describes procedures for the following topics:

 

l

Connect to the tablet interface

 

l

Confidence monitoring using the tablet interface 

 

l

Verify disk space via the tablet interface

 

l

Control recording via the tablet interface

 

l

Switch to the full admin interface

Connect to the tablet interface

To get started with the tablet interface you can connect to it in one of the following ways. 

The device connecting to the tablet interface must be on the same network as the Standalone 
VGA Grid or must be physically connected to it via USB.

 

l

Use the browser over Ethernet

 

l

Use tethering on your device

 

l

Use the mobile version of Epiphan Connect

Use the browser over Ethernet

You can connect to the tablet interface with a browser on your admin computer, tablet, or touch-screen 
device.

To connect to the tablet interface:

 1.  Connect to the admin interface using your preferred connection mechanism. See 

Connect to the admin 

interface

.

 2.  Login as admin or operator.

 3.  Modify the URL in the browser to have /m after the existing text and press Enter; the tablet interface 

opens. (If you forget the /m, the system will direct you to the mobile or standard interface, depending 
on information sent by your device's browser).             

249

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

ABB ACS 600 Startup Manual preview
ACS 600
Brand: ABB Pages: 10
Harman Kardon HD7400 Instruction Manual preview
HD7400
Brand: Harman Kardon Pages: 12
Harman Kardon CD491 Owner'S Manual preview
CD491
Brand: Harman Kardon Pages: 15
3onedata 1200 Series Quick Installation Manual preview
1200 Series
Brand: 3onedata Pages: 3
Cambridge Audio Minx Xi Quick Start Manual preview
Minx Xi
Brand: Cambridge Audio Pages: 4
Cambridge Audio azur 540C V2 Supplementary Manual preview
azur 540C V2
Brand: Cambridge Audio Pages: 2
Cambridge Audio DacMagic 200M Quick Start preview
DacMagic 200M
Brand: Cambridge Audio Pages: 4
Cambridge Audio Azur 640C User Manual preview
Azur 640C
Brand: Cambridge Audio Pages: 84
Cambridge Audio azur 540D Manual preview
azur 540D
Brand: Cambridge Audio Pages: 8
Cambridge Audio Minx Air100 Setup Manual preview
Minx Air100
Brand: Cambridge Audio Pages: 2
Cambridge Audio DVD57RWi User Manual preview
DVD57RWi
Brand: Cambridge Audio Pages: 35
NAD M56 Owner'S Manual preview
M56
Brand: NAD Pages: 30
HANTZ HELIOS H4000 Manual preview
HELIOS H4000
Brand: HANTZ Pages: 4
Brandt BCD510USB Instruction Manual preview
BCD510USB
Brand: Brandt Pages: 66
ADF Web HD67B31 Series User Manual preview
HD67B31 Series
Brand: ADF Web Pages: 30
Audiophonics RASPTOUCH ES9018K2M User Manual preview
RASPTOUCH ES9018K2M
Brand: Audiophonics Pages: 30
StarTech.com ET91000LCOAM Manual preview
ET91000LCOAM
Brand: StarTech.com Pages: 24
TA D-LOGG Manual preview
D-LOGG
Brand: TA Pages: 32

Brands by name

Popular brands

Load more brands