manualshive.com logo in svg

epiphan video Standalone VGA Grid, User Manual

The Epiphan Standalone VGA Grid is a cutting-edge hardware device that allows users to connect multiple VGA sources to a single display. You can easily set up and operate this device with the help of our comprehensive User Manual, available for free download on our website. Unlock the full potential of your Epiphan Standalone VGA Grid with our detailed instructions and troubleshooting tips, seamlessly accessible at manualshive.com.

Share
Download
background image

Standalone VGA Grid User
Guide                                     

Install firmware

 6.  Click 

download 

from the red box that appears at the top left of the admin interface; the firmware is 

downloaded and immediately starts to install and the firmware update box changes to have a cancel 
button.

Do not interrupt power to the system during the firmware upgrade.

 7.  When the firmware update is complete, the message lets you know it is going to reboot.

 8.  Wait for the system to restart. Depending on the upgrade, a disk rebuild may be required, causing the 

restart process to take much longer than usual.

 9.  Connect to the admin interface using your preferred connection mechanism. See 

Connect to the admin 

interface

.

 10.  Login as admin.

 11.  Select the 

Firmware Upgrade 

link in the Configuration menu; the firmware upgrade page opens.

 12.  Verify that the firmware version is the expected new version.

Although unexpected, it is possible the firmware update fails. In this case,  collect system information such as 
device serial number and, if known, the previous firmware version along with the new firmware version and 
contact [email protected]

Install firmware from a file

Before getting started, ensure you have the firmware file accessible from your admin computer.

To install new firmware from a file:

 1.  Connect to the admin interface using your preferred connection mechanism. See 

Connect to the admin 

interface

.

 2.  Login as admin.

265

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

Panasonic DMP-BD90 Basic Owner'S Manual preview
DMP-BD90
Brand: Panasonic Pages: 12
NAD C 568 Owner'S Manual preview
C 568
Brand: NAD Pages: 16
NAD D 1050 Quick Setup Manual preview
D 1050
Brand: NAD Pages: 2
NAD C375BEE Mounting Instructions preview
C375BEE
Brand: NAD Pages: 2
NAD T 514 Datasheet preview
T 514
Brand: NAD Pages: 2
NAD 523 Product Manual preview
523
Brand: NAD Pages: 2
Z3 Technology Z3-MVE-20 User Manual preview
Z3-MVE-20
Brand: Z3 Technology Pages: 18
Z3 Technology Z3-DM8107-RPS User Instructions preview
Z3-DM8107-RPS
Brand: Z3 Technology Pages: 23
YOTON YM04 User Manual preview
YM04
Brand: YOTON Pages: 8
American DJ Audio DCD PRO 250 Instruction Manual preview
DCD PRO 250
Brand: American DJ Audio Pages: 18
Lika SMA5 Series Mounting Instructions preview
SMA5 Series
Brand: Lika Pages: 2
Versus Audio VS MUSIC BOX User Manual preview
VS MUSIC BOX
Brand: Versus Audio Pages: 12
Aiwa XP-EV515 Operating Instructions preview
XP-EV515
Brand: Aiwa Pages: 2
Harman Kardon HD760 Owner'S Manual preview
HD760
Brand: Harman Kardon Pages: 20
Patton electronics 2702 G.703 User Manual preview
2702 G.703
Brand: Patton electronics Pages: 11
B&B Electronics Parallel Port Input/Output Converter PPIO User Manual preview
Parallel Port Input/Output Converter PPIO
Brand: B&B Electronics Pages: 34
StarTech.com ET91000LCOAM Manual preview
ET91000LCOAM
Brand: StarTech.com Pages: 24
Vitek VT-3776 Manual Instruction preview
VT-3776
Brand: Vitek Pages: 12

Brands by name

Popular brands

Load more brands