Entrematic Ditec DAS200 Technical Manual Download

Page: 43 / 56

IP2266EN

Extended Hold Open Time Function (00÷01)

+ 5s hold open time on doors often reopening during closing.

= Off.

= On.

Control unit electronic mode selector group (01÷10)

FUTURE USE

MOTOR CONTROL PARAMETERS

Parameter

Description

Factory

setting

Installation

setting

Motor Type (15÷17)

15= DAS200
16= DAS200HD / DAS200RF
17= DAS200RG

FACTORY SET

Max Motor Power (03÷15)

The max amount of power the motor can be supplied with.

DAS902MP PLUS MODULE PARAMETERS

Parameter

Description

Factory

setting

Installation

setting

Function Select terminal 3 - DAS902MP (00÷03)
00

= NO FUNCTION.

= Nurse function. The door will open to partial opening in

operation mode selections EXIT, AUTO and AUTO PARTIAL.

= DO NOT USE.

= Interlock out. When configuring for interlock also set

parameter 6A = 01.

Function Select terminal 4 - DAS902MP (00÷04)
00

= NO FUNCTION.

= Open/Close Function . One impulse opens the door the

next impulse closes the door. Available in operation
mode selections EXIT, AUTO, PARTIAL.

= Interlock disable function. Disables interlock, both doors

can be open at the same time.

= Inner impulse 2 monitoring. Sets inner impulse 2 mo-

nitoring for the second inner impulse on the DAS902MP
unit. Set also parameter 93 = 03.

= Interlock in. When configuring for interlock also set

parameter 6A = 01.

Open/Close Timeout, terminal 4 - DAS902MP (00÷60
minutes)

The time set in this parameter controls when a door shall
start closing automatically if left open by an Open/Close
impulse.

00 min

= no automatic closing.

Summary of Contents for Ditec DAS200

























































Search results

Summary of Contents for Ditec DAS200

Reviews:

Related manuals for Ditec DAS200

Brands by name

Popular brands

Entrematic Ditec DAS200, Technical Manual

Search results

Summary of Contents for Ditec DAS200

Reviews:

Related manuals for Ditec DAS200

Brands by name

Popular brands