Entrematic Ditec DAS200 Technical Manual Download

Page: 30 / 56

IP2266EN

NOTE

: for DAS200RF follow the start up procedure indicated in the DAS200RFKA kit

manual.

Before performing any type of operation, make sure that the automation is turned off
and the batteries are disconnected.

Start-up and adjustment must be performed in the following order when the automation is installed:

Connect the accessories, opening and safety sensors, blocking device, batteries and selector.

Jumper the safety contacts

1-2

1-3

1-4

8-9

8-11

on the control panel and

1-5

on plus

module DAS902MP, if not used.

Connect the mains power supply to the automation.

4. Set the following parameters

Parameter

Description

Settings

Lock configuration (main control)

Set ONLY if installed bistable lock DAS802LOKB. 12= bistable
lock.

= No lock.

= Antipanic lock (locked with power – LDP).

= Standard lock (locked without power – LD) and bi-

stable lock (LDB).

Central presence sensor test

= None (factory setting).

= Presence sensor 1 (set if a presence sensor with

monitoring is installed).

= Presence sensor 1 and 2 (set if two presence sensors

with monitoring are installed).

Selection of opening direction

= right hand opening for single door wing automation.

= left hand opening for single door wing automation and

for double door automation (factory setting).

Inner Impulse (motion) Monitoring

According to EN16005 or DIN18650 it is a demand to have
Inner impulse monitoring= On in escape routes.

= Disables monitoring.

= Enables monitoring.

NOTE

: on DAS200RF set to 01.

NOTE

: on DAS200RG this parameter is set to 01.

Side presence sensor test

= None ( factory setting)

= Presence sensor 1 (set if a presence sensor with

monitoring is installed).

= Presence sensor 1 and 2 (set if two presence sensors

with monitoring are installed).

Selection of the type of automation

= Automation with one door wing.

= Automation with two door wings.

Lock Configuration, terminal 16-17
DAS902MP

NOTE

: Set ONLY if installed bistable lock DAS802LOKB.

= bistable lock

NOTE

: Parameter 10 ( Emergency Unit Monitoring ) on DAS00RG is not visible and it is

set up on

= redundant monitoring

10. Start up

Summary of Contents for Ditec DAS200

























































Search results

Summary of Contents for Ditec DAS200

Reviews:

Related manuals for Ditec DAS200

Brands by name

Popular brands

Entrematic Ditec DAS200, Technical Manual

Search results

Summary of Contents for Ditec DAS200

Reviews:

Related manuals for Ditec DAS200

Brands by name

Popular brands