Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide
61
Mid 2 Q
1.0 to 40.0
Identical to the Mid 1 Q parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Gain
Off, -49.5dB to +24dB
Identical to the Mid 1 Gain parameter, and is used to
control different bandwidths within the mid range.
HiShelf Gain
Off, -49.5dB to +24dB
Sets the amount of boost or cut applied to the high
frequency shelf.
EQ Output
Off, -49.5dB to +24dB
Controls the gain coming out of the parametric EQ.
Dly1 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the first independent
delay.
Dly1 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback
-99% to +99%
Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping
100Hz to 21.2kHz
Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly1 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly2 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the second
independent delay.
Dly2 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
33
3
3999
9 EEEEQ
Q
Q
Q
→
C
C
C
Coooom
m
m
mpppp
→
G
G
G
Gaaaatttteeee
EQ
→
Comp
→
Gate combines an EQ with a full feature stereo compressor. When using high compressor
ratios, this insert effect functions as a limiter. This effect operates by compressing (attenuating) signals
above the threshold and passing the signals below the threshold. With higher ratios and lower
thresholds, this effect can be used to create sustain.
Parameter
Range
Description
EQ Input
Off, -49.5dB to +24dB
Adjusts the input level trim to the EQs to eliminate the
possibility of clipping boosted signals.
Lo Shelf Fc
10Hz to 20.0kHz
Sets the center of the low frequency EQ.
LoShelf Gain
Off, -49.5dB to +24dB
Sets the amount of boost or cut applied to this low
frequency shelf.
Mid 1 Fc
10Hz to 20.0kHz
Sets the center of the mid frequency parametric.
Mid 1 Q
1.0 to 40.0
This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.
Mid 1 Gain
Off, -49.5dB to +24dB
Sets the amount of boost or cut applied to this mid
frequency band.
Mid 2 Fc
10Hz to 20.0kHz
Identical to the Mid 1 Fc parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Q
1.0 to 40.0
Identical to the Mid 1 Q parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Gain
Off, -49.5dB to +24dB
Identical to the Mid 1 Gain parameter, and is used to
control different bandwidths within the mid range.
HiShelf Fc
10Hz to 20.0kHz
Sets the center frequency of the high frequency shelf.
HiShelf Gain
Off, -49.5dB to +24dB
Sets the amount of boost or cut applied to this high
frequency shelf.
EQ Output
Off, -49.5dB to +24dB
Controls the gain coming out of the parametric EQ.
