Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide
39
HF Damping
100Hz to 21.2kHz
Controls the rate of attenuation of high frequencies in
the decay of the reverberation. Increasing the value of
this parameter will gradually filter out (dampen) more
and more high frequency energy.
HF Bandwidth
100Hz to 21.2kHz
Acts as a low pass filter on the signal going into the
reverb, controlling the amount of high frequencies that
will pass. The higher the setting, the more high
frequencies are allowed to pass.
Diffusion 1
0 to 100
Smears the input signal transients, to diffuse and
smooth the sound. Lower values will cause impulse
sounds to appear as a series of discrete echoes, while
higher values tend to increase the smear (smoother
sounding with fewer discrete echoes). We recommend
settings of 50 for starters.
Diffusion 2
0 to 100
This parameter, similar to and in series with Diffusion 1,
controls lower frequency ranges.
Definition
0 to 100
Controls the rate at which echo density is increased with
time. Setting this too high can cause the echo density to
build at a rate which exceeds the decay rate.
22
2
2000
0 D
D
D
DD
D
D
DLLLL
→
C
C
C
Chhhhoooorrrruuuussss
DDL
→
Chorus combines four independent, controllable digital delays with a chorus.
PPP
Paaaarrrraaaam
m
m
meeeetttteeeerrrr
RRR
Raaaannnnggggeeee
D
D
D
Deeeessssccccrrrriiiippppttttiiiioooonnnn
Dly1 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the first independent delay.
Dly1 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback
-99% to +99%
Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping
100Hz to 21.2kHz
Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly1 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly2 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the second independent delay.
Dly2 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Feedback
-99% to +99%
Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly2 Damping
100Hz to 21.2kHz
Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly2 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly3 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the third independent delay.
Dly3 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly3 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly4 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the fourth independent delay.
Dly4 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
