ENSONIQ ASR-X PRO, User Manual

Page: 53 / 74

Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide 45
HiShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this high
frequency shelf.
EQ Output Off, -49.5dB to +24dB Controls the gain coming out of the parametric EQ.
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the four rates of the modulation applied to the
delay time of the chorus.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
LFO Phase -180deg to +180deg Controls the relative phase between left and right LFOs.
Chorus Depth 0.0ms to 25.0ms Controls the amount of modulation.
ChorusCenter 0.0ms to 50.0ms Controls the delay times within the chorus. Adjusting
this parameter will change the tonal character of the
chorus.
Spread (wide stereo to mono) This parameter offers control of the synthesized stereo
field. The farthest counterclockwise setting of the Value
knob offers true stereo, the middle setting forces the left
and the right into the center (mono), and turning the
Value knob fully clockwise inverts the left and right
signal.
22
2 2666 6 D
D
D Diiiisssstttt →
FFFFllllaaaannnnggggeeeerrrr
Dist
→
Flanger combines a distortion with a flanger.
PPP Paaaarrrraaaam m m meeeetttteeeerrrr RRR Raaaannnnggggeeee D D D Deeeessssccccrrrriiiippppttttiiiioooonnnn
Dist LPF Fc 10Hz to 20.0kHz Filters out high frequencies prior to the distortion.
Dist Offset -99% to +99% Adjusts the balance of even-to-odd-generated
harmonics.
Dist Gain Off, -49.5dB to +48dB Controls the gain going into the distortion effect. This
will boost the signal level up to 48 dB. For more
distortion, use a high input level gain and turn the
distortion volume down to keep the volume under
control. For less distortion, use a low gain input level
and a higher output volume.
Dist Curve Soft, Medium 1, Medium 2,
Hard, Buzz
Selects the type of clipping produced by the distortion.
The curves range from tube-like distortion (Soft) to
nasty distortion (Buzz).
Dist Volume Off, -99dB to 0.0dB Controls the volume of the distortion effect. Generally, if
the distortion gain is set high, set this parameter lower.
Post VCF Fc 10Hz to 7.10kHz Determines the distortion filter cut off frequency. Higher
values have a brighter sound. This parameter can be
modulated by any continuous MIDI controller for a
wah-wah pedal effect.
Post VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at
the filter cutoff point. While the Fc (filter cutoff)
parameter determines where (at what frequency) this
peak will occur, the Q setting controls the sharpness of
the peak.
Dist Dry Lev Off, -49.5dB to 0.0dB Controls the amount of dry signal to be mixed with the
distorted signal.
EQ Input Off, -49.5dB to +24dB Adjusts the input level trim to the EQs to eliminate the
possibility of clipping boosted signals.
LoShelf Fc 10Hz to 20.0kHz Sets the center of the low frequency EQ.
LoShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this low
frequency shelf.
Mid 1 Fc 10Hz to 20.0kHz Sets the center of the mid frequency parametric.
Mid 1 Q 1.0 to 40.0 This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.