ENSONIQ ASR-X PRO, User Manual

Page: 46 / 74

Insert Effect Parameters
38 ENSONIQ ASR-X Pro UserÕs Guide
Mid 1 Q 1.0 to 40.0 This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.
Mid 1 Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this high
frequency shelf.
HiShelf Fc 10Hz to 20.0kHz Sets the center frequency of the high frequency shelf.
HiShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this shelf.
EQ Output Off, -49.5dB to +24dB Controls the gain coming out of the parametric EQ.
Rev Mix Full Dry to Full Wet Controls the reverb mix.
Decay 0.0sec to 10.0sec Controls the amount of time it takes for the reverb to
decay after the input signal stops.
HF Damping 100Hz to 21.2kHz Controls the rate of attenuation of high frequencies in
the decay of the reverb. Increasing the value of this
parameter will gradually filter out (dampen) more and
more high frequency energy.
HF Bandwidth 100Hz to 21.2kHz Acts as a low pass filter on the signal going into the
reverb, controlling the amount of high frequencies that
will pass. The higher the setting, the more high
frequencies are allowed to pass.
Diffusion 1 0 to 100 Smears the input signal transients, to diffuse and
smooth the sound. Lower values will cause impulse
sounds to appear as a series of discrete echoes, while
higher values tend to increase the smear (smoother
sounding with fewer discrete echoes). We recommend
settings of 50 for starters.
Diffusion 2 0 to 100 This parameter, similar to and in series with Diffusion 1,
controls lower frequency ranges.
Definition 0 to 100 Controls the rate at which echo density is increased with
time. Setting this too high can cause the echo density to
build at a rate which exceeds the decay rate.
11 1 1999 9 SSSSppppiiiinnnnnnnneeeerrrr → RRR Reeeevvvv
Combines a pseudo-three dimensional panner with the standard reverb.
PPP
Paaaarrrraaaam
m
m meeeetttteeeerrrr
RRR
Raaaannnnggggeeee
D D
D Deeeessssccccrrrriiiippppttttiiiioooonnnn
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the rate of modulation applied to the spinner.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for
modulation.
LFO Phase -180deg to +180deg Controls the relative phase between the left and right
and front and back LFOs. Set this to
±
90 deg for circular
motion.
DDL Mod Depth 0.0ms to 10.0ms Controls the left to right mod depth of delay time. Try
setting this to 0.3 ms for average head size.
DDL ModCenter 0.0ms to 50.0ms Fixed delay time.
Level Mod 0% to 100% Left to right LFO mod depth to level.
L-to-R Mod 0% to 100% Left to right LFO mod depth to filter.
F-to-B Mod 0% to 100% Front to back LFO mod depth to filter. If the sum of the
L-to-R Mod and F-to-B Mod is greater than 100%, the
filter can ÒthumpÓ as it closes down.
Cancellation -99% to +99% Sets the depth and phase of the opposite speaker
cancellation signal.
Rev Mix Full Dry to Full Wet Controls the dry/wet mix of the reverb.
Decay 0.0sec to 10.0sec Controls the amount of time it takes for the reverb to
decay after the input signal stops.