manualshive.com logo in svg

Ensemble Designs Avenue Express Control Panel, Data Pack, Page: 4 / 19

Share
Download
Ensemble Designs Avenue Express Control Panel Data Pack Download Page 4

Avenue Express Control Panel

Warning

Rick of electric shock. Qualifed service personael should only access
power supply after frame has been unplugged from power.

EXPRESS CONTROL PANEL INSTALLATION

The 1 RU Avenue Express Control Panel is designed to be installed in a standard 19 inch
rack with four customer-supplied standard rack screws. This section explains any physical
installation and cabling instructions necessary for using Avenue Express Control Panels.

After physical installation, network configuration of the Express Panel and System
parameter such as LED brightness can be set up using the Local controls in the Express
Panel menus. Refer to the Configuration section of this data pack.

Cabling

Network connection of an Express Panel is made on the rear of the panel as illustrated
below. The Express Panel can Avenue frames through via Ethernet, through an AveNet
connection, or with a serial interface.

AveNet:

AveNet

is the Avenue control bus that allows communication between frames by the

System Control modules in each frame. Up to 20 frames can be connected on each
individual AveNet network. Any number of AveNet networks can then be connected
together via Ethernet. AveNet connection between frames requires looping between 

Express Panel–4

Express Control Panel Rear Connectors

AveNet RJ11 Connector Pinout

Summary of Contents for Avenue Express Control Panel




















Reviews:

No comments