Modem: Regulatory Notices
FCC - Antenna - Wireless Products only
The antenna intended for use with this unit meets the requirements for mobile operat-
ing configurations and for fixed mounted operations, as defined in 2.1091 and 1.1307
of the FCC rules for satisfying RF exposure compliance. If an alternate antenna is
used, please consult user documentation for required antenna specifications.
FCC - 47 CFR Part 15 Regulation
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the 47 CFR rules. Operation of this device is sub-
ject to the following conditions: (1} This device may not cause harmful interference,
and (2} this device must accept any interference that may cause undesired operation.
Industry Canada Class B Notice
This Class B digital apparatus meets all requirements of the Canadian Interfer-
ence-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Reglement
Canadien sur le matériel brouilleur.
This device complies with Industry Canada RSS Appliance radio exempt from licens-
ing. The operation is permitted for the following two conditions:
1. the device may not cause harmful interference, and
2. the user of the device must accept any interference suffered, even if the
interference is likely to jeopardize the operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appar-
eils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Industry Canada and FCC
This device complies with Industry Canada license-exempt RSS standard(s) and part
15 of the FCC rules. Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS exemptes de licence standard
(s) et la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux
conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
EMC, Safety, and R&TTE Directive Compliance
The CE mark is affixed to this product to confirm compliance with the following Euro-
pean Community Directives:
Council Directive 2004/108/EC of 15 December 2004 on the approximation of the
laws of Member States relating to electromagnetic compatibility;
and
Council Directive 2006/95/EC of 12 December 2006 on the harmonization of the laws
of Member States relating to electrical equipment designed for use within certain
voltage limits;
and
Council Directive 2011/65/EU on the restriction of the use of certain hazardous sub-
stances in electrical and electronic equipment;
and
Council Directive 1999/5/EC of 9 March 1999 on radio equipment and telecommuni-
cations terminal equipment and the mutual recognition of their conformity.
Checking the Mobile Connect Modem LEDs
The Enphase Mobile Connect modem has the following status LEDs
• Power
• LS
• Signal
The following tables list LED indicator status. The LEDs may be difficult
to see if viewed from an angle. View the LEDs from directly ahead.
LED
Indicates
Off
DC power not present
On
DC power present
Power
LED
Indicates
Lit solid
The modem is not registered on
the cellular network.
Flashing
The modem is registered on the
cellular network.
LS (Link Status)
Signal
LEDs
Description
Indicates
All off
Very weak signal
LED 1 ON
Weak signal
LED 1 and 2 ON
Good signal
LED 1, 2, and 3 ON
Very good signal
Issue
Action
No communication with
Enlighten after connecting
the cellular modem to the
IQ Envoy.
1. Disconnect the USB cable.
2. Power cycle the IQ Envoy.
3. Wait until the IQ Envoy boots up completely.
4. Reconnect the cellular modem USB cable.
Modem Troubleshooting