ENPC EP-PV12 User Manual Download Page 33

Page: 33 / 53

ROM PCI/ISA BIOS (2A59GECA)

BIOS FEATURES SETUP

AWARD SOFTWARE, INC

Virus Warning

: Disabled

Video BIOS Shadow

: Enabled

CPU Internal Cache

: Enabled

C8000 - CBFFF Shadow

: Disabled

External Cache

: Enabled

CC000 - CFFFF Shadow

: Disabled

Quick Power On Self Test

: Disabled

D0000 - D3FFF Shadow

: Disabled

Boot Sequence

: A,C,SCSI

D4000 - D7FFF Shadow

: Disabled

Swap Floppy Drive

: Disabled

D8000 - DBFFF Shadow

: Disabled

Boot Up Floppy Seek

: Enabled

DC000 - DFFFF Shadow

: Disabled

Boot Up NumLock Status

: ON

Boot Up System Speed

: High

Gate A20 Option

: Fast

Typematic Rate Setting

: Disabled

Typematic Rate (Chars/Sec) : 6
Typematic Delay (Msec)

: 250

Security Option

: Setup

PCI/VGA Palette Snoop

: Disabled

ESC : Quit



: Select Item

OS Select For DRAM>64MB : Non-OS2

: Help

PU/PD/+/- : Modify

Report No FDD for WIN95

: Yes

: Old Values

(Shift) F2 : Color

: Load BIOS Defaults

: Load Setup Defaults

Figure 3-3 BIOS Feature Setup Screen

Virus Warning

When enabled, BIOS warns the user when any program

attempts to write or format the boot sector and allows the user

to intervene.

Cache Control

CPU Internal Cache/External Cache: These two categories

speed up memory access. The default value is enable.

3. BIOS SOFTWARE

3-4 BIOS Features Setup (Continue…)

Boot Up Features

After power on the system, BIOS will perform a series of

device initializations and diagnostic tests.

Quick Power On Self Test: If it set to Enabled, BIOS will

skip some check items during POST.

EP-PV12 User’s Manual

Summary of Contents for EP-PV12






















































Search results

Summary of Contents for EP-PV12

Reviews:

Related manuals for EP-PV12

Brands by name

Popular brands

ENPC EP-PV12, User Manual

Search results

Summary of Contents for EP-PV12

Reviews:

Related manuals for EP-PV12

Brands by name

Popular brands