ENPC EP-PV12 User Manual Download Page 43

Page: 43 / 53

Enabled:

Enable Onboard 1

channel IDE port.

Disabled:

Disable Onboard 1

channel IDE port. When

use On-card (PCI or ISA card) IDE connector.

Onboard Primary PCI IDE:

The default value is

Enabled.

Enabled:

Enable Onboard 1

channel IDE port.

Disabled:

Disable Onboard 1

channel IDE port. When

use On-card (PCI or ISA card) IDE connector.

IDE Primary Master PIO:

The default value is Auto.

Auto:

BIOS will automatically detect the Onboard

Primary Master PCI IDE HDD Accessing

mode.

Mode 0-4:

Manually set the IDE Accessing mode.

IDE Primary Slave PIO:

The default value is Auto.

Auto:

BIOS will automatically detect the Onboard

Primary Slave PCI IDE HDD Accessing

mode.

Mode 0-4:

Manually set the IDE Accessing mode.

IDE Secondary Master PIO:

The default value is Auto.

Auto:

BIOS will automatically detect the Onboard

Secondary Master PCI IDE HDD Accessing

mode.

Mode 0-4:

Manually set the IDE Accessing mode.

IDE Secondary Slave PIO:

The default value is Auto.

Auto:

BIOS will automatically detect the Onboard

Secondary Slave PCI IDE HDD Accessing

mode.

Mode 0-4:

Manually set the IDE Accessing mode.

3. BIOS SOFTWARE

3-8 Integrated Peripherals (Continue…)

Onboard FDC Controller:

The default value is Enabled.

Enabled:

Enable the Onboard I/O CHIP’s floppy drive

interface controller.

EP-PV12 User’s Manual

Summary of Contents for EP-PV12






















































Search results

Summary of Contents for EP-PV12

Reviews:

Related manuals for EP-PV12

Brands by name

Popular brands

ENPC EP-PV12, User Manual

Search results

Summary of Contents for EP-PV12

Reviews:

Related manuals for EP-PV12

Brands by name

Popular brands