background image

Table of Contents

page

Introduction
Features and Functionality at a Glance
Contents
Front Panel Features:

Rear Panel Features:

Troubleshooting
Technical Data
Tube Map, Tube Exchange Service
Wiring of Principal Connectors

Note:

:

Handling and Care

Input; Clean (Gain), Bright, Lead (Gain)
EQ section: Bass, Middle, Treble, Shape (Contour)
Lead Control Features: Lead Presence, Lead Volume
Channel selection Clean/Lead, Gain Low/High

Stand By, Power

Poweramp Output 4, 8, 16 Ohms
Poweramp Output: Cabinet options

Power Amp section: Master A/B

Mains, Mains Fuse
S.A.C. Port for Z-9 or Z11-S.A.C., Footswitch Ports

You'll find an ancillary pamphlet accompanying this owner's manual entitled
Instructions for the Prevention of Fire, Electrical Shock and Injury.
Be sure to read it before you plug in and power up the amp!

Technical specifications are subject to change without notice.

Noise Gate: Threshold Level
FX Loop: Send, Return, and Balance

Remote Control Options
Configuration table for Z-9 settings

CAUTION! Please read and heed the following:

4
5
6

6, 7
7, 8
8
8, 9
9, 10
10

10, 11
11, 12
13
14
14
15

15, 16
16, 17
18
19
20
21
22

3

Summary of Contents for Artist Edition E651

























Reviews: