ENFORCER SLI 820R/-4
Tech Manual
Page 9
+12VDC
Factory horn
button
Ø
(-)
Alarm BROWN/WHITE wire
(honking horn output, tr.
ground, 200mA max.)
Factory
horn
Factory
horn
relay
Fig. 9 — (-) Ho nking facto ry ho rns
NO TE — If there is no facto ry ho rn relay, o r if it draws
mo re than 2 0 0 mA, a separate o ptio nal 3 0 A relay must
be used with the BRO WN/ WHITE wire.
Fig. 1 0 — 2 nd channe l o utput
Alarm BLACK/WHITE wire
(2nd channel output, tr.
ground, 200mA max.)
Ø
To optional accessory
(positive switched)
Ø
+12V
Negative-triggered domelights:
GRAY/BLACK wire
Ø
+12V
BLUE wire (on connector 2)
+12V
Door switch
Domelight
Ø
Positive-triggered domelights:
GRAY/BLACK wire
Ø
PURPLE wire (on connector 2)
+12V
Domelight
+12V
Door switch
Ø
Fig. 1 1 — Co nne cting to the
do me lig hts (po sitive o r ne g ative )
A. O utput — Disarms alarm and supplies a
2 0 0 mA transisto r g ro und o utput as lo ng as
a valid sig nal is received if the transmitter
butto n is pressed fo r 2 secs. Fo r safety, 2 nd
channel o utput o perates o nly:
(1 ) If the ig nitio n switch is O FF; o r
(2 ) If a car do o r is o pen while the
ig nitio n switch is O N.
B.
C o nnectio n — C o nnect the BLAC K/ WHITE
WIRE to a 3 0 A relay to co ntro l trunk release
o r o ther accesso ry. NEVER C O NNEC T THE
BLAC K/ WHITE WIRE DIREC TLY TO AN
O PTIO NAL AC C ESSO RY, AS THIS WILL
BURN O UT THE 2 ND C HANNEL O UTPUT,
AND PO SSIBLY THE ENTIRE ALARM BRAIN.
Connector 3 (6-pin connector)
GRAY/BLACK WIRE (domelights), fig. 11
A. O utput — Supplies a 2 0 0 mA transisto r
g ro und o utput in o ne o f three situatio ns:
(1 ) When the alarm is disarmed, this wire
turns the do melig hts o n fo r 3 0 seco nds,
o r until the ig nitio n key is turned O N.
(2 ) When the alarm is trig g ered, this wire
flashes the do melig hts.
(3 ) When the ig nitio n- co ntro lled do melig ht is
enabled, turning O FF the ig nitio n will
turn O N the do melig ht fo r 3 0 seco nds.
Fig. 8 — Co nne cting to trunk & ho o d
pin switche s
×
Alarm BLUE/WHITE wire (neg.
hood/trunk trigger input)
Trunk pin switch
Hood pin switch
+12VDC
Trunk light
×
Alarm BLUE/WHITE wire (neg.
hood/trunk trigger input)
Hood pin switch
Diode
1N4001
Hood/trunk
switch
Fig. 7 — Co nne cting to the
trunk lig ht & ho o d pin switch
Domelight
×
Alarm PURPLE wire (pos. door trigger input)
+12VDC
Fig. 6 — Co nne cting to the
po sitive do o r trig g e rs
Door switch
B.
C o nnectio n — C o nnect the G RAY/ BLAC K
WIRE via a 3 0 A relay to the do melig hts.
Never co nnect the g ray/ black wire directly to
the do melig hts, as this will burn o ut the
do melig ht o utput, and po ssibly the entire
alarm brain.