Endress+Hauser RMA42 Operating Instructions Manual Download Page 52

Page: 52 / 64

Appendix

RMA42

Hauser

11.2

Display menu

AI1 Minmax-reset

Only available if "Yes" was
configured in the
Setup>Analog in 1>Allow
reset menu.

Yes

Resets the minimum and maximum values saved for analog input 1.

AI2 Minmax-reset

Only available if "Yes" was
configured in the
Setup>Analog in 2>Allow
reset menu.

Yes

Resets the minimum and maximum values saved for analog input 2.

Cv1 Minmax-reset

Only available if "Yes" was
configured in the Setup >
Calc value 1 > Allow reset
menu.

Yes

Resets the minimum and maximum values saved for math 1.

Cv2 Minmax-reset

Only available if "Yes" was
configured in the Setup >
Calc value 2 > Allow reset
menu.

Yes

Resets the minimum and maximum values saved for math 2.

Analog in 1

Off
Unit
Bar graph
Bargr + unit

Tag + unit

Configures the display for analog input 1. If the parameter is set to ‘Off’, the channel is not
displayed.

Analog in 2

Off
Unit
Bar graph
Bargr + unit

Tag + unit

Configures the display for analog input 2. If the parameter is set to ‘Off’, the channel is not
displayed.

Calc value 1

Off

Unit
Bar graph
Bargr + unit
Tag + unit

Configures the display for math 1. If the parameter is set to ‘Off’, the channel is not displayed.

Calc value 2

Off

Unit
Bar graph
Bargr + unit
Tag + unit

Configures the display for math 2. If the parameter is set to ‘Off’, the channel is not displayed.

Contrast

1 to 7

Configures the contrast

Brightness

1 to 7

Configures the brightness

Alternating time

3 seconds

5 seconds

10 seconds

Configures the time for toggling between the channels displayed.

Summary of Contents for RMA42

































































Search results

Summary of Contents for RMA42

Reviews:

Brands by name

Popular brands

Endress+Hauser RMA42, Operating Instructions Manual

Search results

Summary of Contents for RMA42

Reviews:

Brands by name

Popular brands