Endress+Hauser Proservo NMS5, Operating Instructions Manual

Page: 106 / 162

Proservo NMS5
106 Hauser
13 Matrix
13.1 Programming Matrix
0
123
4567
89
0 1 2 3
V
H
NMS5 Programming Matrix (Static Matrix)
GROUP MESSAGE
Display Text Parameters, unit, etc Default Data
MEASURED VALUE 1 MEASURED VALUE 2
OPERATION MORE FUNCTION
16000.00mm
MEASURED LEVEL
Display
0.0 mm
ULLAGE LEVEL
0.0°C LIQUID TEMP.
Display
STOP
OPERATION 16000
See operation commands below Select (50)
CALIBRATION MATRIX OF Select
Display
See status table below
OPERATING STATUS
STOP
Display
DEV(1)
Display
0.0 mm
0.0 mm
UPPER INTERF. LEV. Display
DEV(2)
Display
Display
UNBALANCED
BALANCING STATUS
Display
MIDD. INTERF. LEV
Display
Display
BOTTOM LEVEL
0.0 mm
0.0°C
GAS TEMPERATURE
LEVEL
LEVEL
OPERAT.BY NRF
Display
Display
98 627 8:21:00
CALENDER
Currect data
Display
Display
Display
Currect data
Currect data
ALARM CONTACT 0
NO ALARM
NO ALARM LA 0 0 0 0 OPERAT. BY HOST
1.000 g/ml
UPPER DENSITY 0.000 - 3.000
Display/Set (50)
1.000 g/ml MIDDLE DENSITY 0.000 - 3.000
DENSITY BOTTOM 1.000 g/ml
0.000 - 3.000
Display/Set (50)
Display/Set (50)
0 mm
ZERO POINT
Display
NO ERROR
DIAGNOSTIC CO 0 Currect data
Currect data
Display
Display 98 627 752 0 0
MPU:START ACT
0 ACCESS CODE
0, 50, 51, 777
Set
0
8424
DEVICE ID
SOFTWARE VERSION
Display
Display
SPAN
LENGTH UNIT
mm
16000.0 mm
0.0 mm
LEVEL DATA Display
WATER BOTTOM 0.0 mm
Display
When new NMS status is selected at GVH=272, new status codes are showed at matrix position GVH=021 as follows;
Code
Meaning
NMS Display
Code
Meaning
NMS Display
0 1 2 3 4 5 6 7 8 9 10
.ODElNITION
Displacer at reference Displacer hoisting up Displacer going down Displacer stop Level measurement, balanced Upp. I/F level, balanced Midd. I/F level, balanced Bottom meas. balanced
5PPER$ENSlNISHED -IDDLE$ENSlNISHED
REFERENCE UP DOWN STOP LEVEL UPPER.INTERF
.LEV
.
MIDD.INTERF
.LEV
.
BOTTOM LEVEL UPPER DENSITY MIDDLE DENSITY
12 13 14 15 16 17 18 19 20 21
Release over tension Calibration activated Seek level Follow level Seek Upper Density Seek Middle Density Seek Density Bottom Seek Upper I/F level Follow up. I/F level Seek Mid. I/F level
RELE. OVER TENS. CAL. ACTIVE LEVEL SEEKING LEVEL FOLLOWING UPP
. DEN. SEEKING
MID. DEN SEEKING BOT
. DEN. SEEKING
UPP
. INT
. SEEKING
UPP
. INT
. FOLLOWING
MID.INT
.SEEKING
-
24 25 26 27 28 29 30 31 32
Code
Meaning
NMS Display
Not initialised Stopped at High Stop Stopped at Low Stop Repeatability testing Seeking water level W
ater level, balanced
Follow water level Over-/Under tension, Z-Phase, ADC error
NO INITIALIZE UPPER STOP LOWER STOP REPEA
T
ABILITY
W
A
TER SEEKING
W
A
TER LEVEL
W
A
TER FOLLOWING
EMARGENCY ERROR
Operating commands
2. STOP 3. BOTTOM LEVEL 4. UPPER INTERF
. LEVE
5. MIDD. INTERF
. LEVE
6. UPPER DENSITY 7. MIDDLE DENSITY 8. DENSITY BOTTOM 9. REPEA
T
ABILITY
10.W
A
TER DIP
0. LEVEL 1. UP
+ Key
Mode (Code)
OFF
RESET ALM. DIAGNO.
0 - 8
GVH157 Service Mode = ON,
MAINTENANCE (Modbus / HAR
T only)
11
"OTTOM$ENSlNISHED
DENSITY BOTTOM
22
23
Follow Mid. I/F level Seek Bottom level
MID. INT
. FOLLOWING
BOTTOM SEEKING
13 Matrix