Endress+Hauser Memosens COS81E Operating Instructions Manual Download Page 34

Page: 34 / 40

Accessories

Memosens COS81E

Hauser

CYA680

• Flow assembly for hygienic sensors

• For sensor installation in pipes

• Suitable for cleaning in place (CIP) and sterilization in place (SIP)

• Certified biocompatibility as per USP Class VI, FDA-listed seals and hygienic,

electropolished surfaces Ra=0.38 µm (15 µinch)

• Product Configurator on the product page:

www.endress.com/cya680

Technical Information TI01295C

11.1.2 Measuring cable

Memosens data cable CYK10

• For digital sensors with Memosens technology

• Product Configurator on the product page:

www.endress.com/cyk10

Technical Information TI00118C

Memosens data cable CYK11

• Extension cable for digital sensors with Memosens protocol

• Product Configurator on the product page:

www.endress.com/cyk11

Technical Information TI00118C

Memosens laboratory cable CYK20

• For digital sensors with Memosens technology

• Product Configurator on the product page:

www.endress.com/cyk20

11.1.3 Zero-point gel

COY8

Zero-point gel for oxygen and disinfection sensors

• Oxygen-free and chlorine-free gel for the verification, zero point calibration and

adjustment of oxygen and disinfection measuring points

• Product Configurator on the product page:

www.endress.com/coy8

Technical Information TI01244C

11.1.4 Transmitter

Liquiline CM44

• Modular multi-channel transmitter for hazardous and non-hazardous areas

• Hart®, PROFIBUS, Modbus or EtherNet/IP possible

• Order according to product structure

Technical Information TI00444C

Liquiline CM42

• Modular two-wire transmitter for hazardous and non-hazardous areas

• Hart®, PROFIBUS or FOUNDATION Fieldbus possible

• Order according to product structure

Technical Information TI00381C

Liquiline Mobile CML18

• Multiparameter mobile device for laboratory and field

• Reliable transmitter with display and app connection

• Product Configurator on the product page:

www.endress.com/CML18

Operating Instructions BA02002C

Summary of Contents for Memosens COS81E









































Search results

Summary of Contents for Memosens COS81E

Reviews:

Related manuals for Memosens COS81E

Brands by name

Popular brands

Endress+Hauser Memosens COS81E, Operating Instructions Manual

Search results

Summary of Contents for Memosens COS81E

Reviews:

Related manuals for Memosens COS81E

Brands by name

Popular brands