Endress+Hauser Memosens COS81E Operating Instructions Manual Download Page 33

Page: 33 / 40

Memosens COS81E

Accessories

Hauser

Accessories

The following are the most important accessories available at the time this documentation

was issued.

‣

For accessories not listed here, please contact your Service or Sales Center.

11.1 Device-specific accessories

11.1.1 Assemblies (selection)

COS81D with 220 mm length is suitable for all assemblies requiring an installation

length of 225 mm.

Cleanfit CPA875

• Retractable process assembly for sterile and hygienic applications

• For in-line measurement with standard sensors with 12 mm diameter, e.g. for pH, ORP,

oxygen

• Product Configurator on the product page:

www.endress.com/cpa875

Technical Information TI01168C

Flowfit CPA240

• pH/redox flow assembly for processes with stringent requirements

• Product Configurator on the product page:

www.endress.com/cpa240

Technical Information TI00179C

Unifit CPA842

• Installation assembly for food, biotechnology and pharmaceutics

• With EHEDG and 3A certificate

• Product Configurator on the product page:

www.endress.com/cpa842

Technical Information TI00306C

Cleanfit CPA450

• Manual retractable assembly for installing sensors with a diameter of 12 mm and a

length of 120 mm in tanks and pipes

• Product Configurator on the product page:

www.endress.com/cpa450

Technical Information TI00183C

Flowfit CYA21

• Universal assembly for analysis systems in industrial utilities

• For sensors with Ø 12 mm and length 120 mm

• Compact stainless steel assembly with low sampling volume

• Product Configurator on the product page:

www.endress.com/CYA21

Technical Information TI01441C

Flexdip CYA112

• Immersion assembly for water and wastewater

• Modular assembly system for sensors in open basins, channels and tanks

• Material: PVC or stainless steel

• Product Configurator on the product page:

www.endress.com/cya112

Technical Information TI00432C

Summary of Contents for Memosens COS81E









































Search results

Summary of Contents for Memosens COS81E

Reviews:

Related manuals for Memosens COS81E

Brands by name

Popular brands

Endress+Hauser Memosens COS81E, Operating Instructions Manual

Search results

Summary of Contents for Memosens COS81E

Reviews:

Related manuals for Memosens COS81E

Brands by name

Popular brands