Endress+Hauser Liquiline To Go CYM290 Operating Instructions Manual Download Page 26

Page: 26 / 64

Calibration

(Automatic calibration with specification of the buffer solution used)

1) Select the number of calibration points and the buffer set as shown in the table

below and press the Start softkey.

Calibration points Auto | 1-point | 2-point | 3-point

Hauser

2.00/4.01/6.98/9.95/11.87

Buffer set

Mettler-Toledo

2.00/4.01/7.00/9.21

Knick CaliMat

2.00/4.00/7.00/9.00/12.00

Ciba

2.06/4.00/7.00/10.00

NIST technical

1.68/4.00/7.00/10.01/12.46

NIST standard

1.679/4.006/6.865/9.180

Hach

4.01/7.00/10.01/12.00

WTW

2.00/4.01/7.00/10.00

Hamilton

2.00/4.01/7.00/10.01/12.00

Reagecon

2.00/4.00/7.00/9.00/12.00

DIN 19267

1.09/4.65/6.79/9.23/12.75

2) Immerse the sensor in the 1st/2nd/3rd buffer solution and press Continue

(repeat this step for each calibration point).

3) Finally, the calibration data will be displayed. You can Apply or Discard these

values.

pH Calibration

1)  In measuring mode, press the Menu softkey.
2)  Select “Configuration” and confirm by pressing E.
3)  Select the desired “Calibration mode”.
4)  Perform the selected calibration as described on the following pages.

Follow the instructions on the display.

Calibration

Note: To abort calibration, you can press

at any time.

Summary of Contents for Liquiline To Go CYM290

































































Search results

Summary of Contents for Liquiline To Go CYM290

Reviews:

Related manuals for Liquiline To Go CYM290

Brands by name

Popular brands

Endress+Hauser Liquiline To Go CYM290, Operating Instructions Manual

Search results

Summary of Contents for Liquiline To Go CYM290

Reviews:

Related manuals for Liquiline To Go CYM290

Brands by name

Popular brands