ENCORP iSAVER DPFC 450 Operating Manual Download Page 7

Page: 7 / 28

– Page 7 –

Standard Specification for iSaver 650 DPFC

Model

iSaver 650

Voltage Input

600 VAC 60Hz

Supply

Three Phase

Configuration

3 Phase – 4 Wire

Rating

650 kVAr

Current Rating

650A

Banks

1x50 + (6x100) kVAr

Sequence

1:2:2:2:2

Logic

The unit is designed to operate in steps of 50 kVAr

Minimum Step

70% of the lowest Bank Capacity (35 kVAr)

Control Operation

Controlled real time switching output based on load requirements.

Controller

Microcontroller based advanced electronic controller

Target Efficiency

> 98% (+/- 3%) for Canadian Voltage and frequency

iSaver Display

3 row crystal clear backlit LCD display of RMS values

Web Monitoring

On Line iSaver parameters display (PF, kVA, kVAh, kW, kWh, kVAr,
kVArh, Hz, V-THD, I-THD, Status, Alarms, Time Integrated data.

Diagnostic feature

iSaver internal key component functional analysis and status display

iSaver Monitor

Displays main and ISaver (panel) parameters locally and remotely

DG operation

Dedicated PF setting for DG operation

Displayed Data

PF, kVA, kVAh, kW, kWh, kVAr, kVArh, Hz, V-THD, I-THD

Main Protection

Short circuit and Over- load protection (MCCB 1000A/50KA-3Pole)

Bank Protection

Short circuit and Over-load protection (MCCB & MCB) and Thermal
safety trip(s). Unit automatically resumes operation once fault is
corrected.

Protection

Thermostats operated over temperature protection of enclosure cham-
bers (Both Front and Capacitor Chamber), Harmonic Reactors and
Capacitors.

Construction

Robust Standalone metal enclosure (indoor application only)

Dimensions

1600 (H) x 1600 (W) x 800 (D) mm

Weight

750Kg [± 3 %]

Mounting

Floor Mounting with Foundation Bolts

Enclosure

Powder coated corrosion resistant sheet steel enclosure (RAL 7035)

Transient protection

Provided

Cable Entry

Top entry provision

Summary of Contents for iSAVER DPFC 450





























Search results

Summary of Contents for iSAVER DPFC 450

Reviews:

Related manuals for iSAVER DPFC 450

Brands by name

Popular brands

ENCORP iSAVER DPFC 450, Operating Manual

Search results

Summary of Contents for iSAVER DPFC 450

Reviews:

Related manuals for iSAVER DPFC 450

Brands by name

Popular brands