![background image](http://html1.mh-extra.com/html/empire-comfort-systems/millivolt-standing-pilot-dvx36fp31l-4/millivolt-standing-pilot-dvx36fp31l-4_installation-instructions-and-owners-manual_2403951037.webp)
39357-0-1018
Page 37
DvvK-4RE vENT KIT INSTALLATION INSTRUCTIONS
CAUTION
Sharp edges, use protective gloves when installing.
Tools Needed for Installation:
•
Sheet metal snips
•
5/16” nut driver
•
Phillips head screwdriver - #2
•
High temperature sealant or furnace cement rated for continu-
ous use at 1,000
o
F minimum
•
Measuring tape
See parts list on page 38 to verify components included in this vent
kit prior to installation.
NOTICE:
If installing onto wood, lap, or vinyl siding, the vinyl siding
kit should be used (sold separately, part number DV-822).
The vinyl siding vent kit, DV-822, is available from Empire Comfort
Systems, Inc. The depth is 3” (76mm), which enables the vent
cap to be extended away from vinyl siding or projections. The wall
depth plus the additional 3” (76mm) depth of the vinyl siding vent
cap extension should not exceed a total depth of 13 3/4” (349mm).
If wall depth exceeds 13 3/4” (349mm), extend system using
6 5/8” (168mm) x 4” (102mm) rigid venting (See Fireplace Instruc-
tions for approved lengths)
See Figure 55.
Installing Wall Thimble/Firestop Assembly
1. Fix fireplace to permanent location. If using rigid venting system,
install up to the location where it will exit the building.
2. Cut hole in wall for wall thimble/firestop assembly into your com
-
bustible wall.
See Figure 54.
Note: On brick or block exterior
wall a 7” (178mm) diameter hole needs to be cut.
Measure the total wall thickness to determine whether or not the
extension thimble is to be used. If the combustible wall depth
is over 5 3/8” (137mm), then the extension thimble should be
used.
See Figure 54
.
3. Install the wall thimble assembly through the framed opening so
the firestop plate is on the interior wall.
See Figure 54.
Telescope
section should extend all the way through the exterior wall. At-
tach with four 10 x 1” screws.
4. When placing the vent cap on an exterior wall covered with
combustibles such as wood, lap, or vinyl siding, install the vinyl
siding kit to the exterior wall sheathing.
11”
9”
NOTE: SPACING FLANGE
INSTALLED TO TOPSIDE
INTERIOR WALL
EXTENSION
THIMBLE
Figure 54
Figure 55
CUTTING VENT TUBES
This is the most important part of the installation.
With the
fireplace (and the rigid venting system if used) fixed to its perma
-
nent location, the 6 5/8” (168mm) diameter air inlet tube and the 4”
(102mm) diameter flue outlet tube are to be marked and cut using
the following procedure.
5. Attach the inlet tube to the outside mounting plate. Align
tinnerman clips on the tabs of the air inlet tube to the holes on
outside mounting plate, and fix with two #10 x 1/2” screws.
6. With the vinyl siding kit installed to wall (if necessary), insert
the 6 5/8” (168mm) diameter tube with outside mounting plate
attached through hole in wall. Connect to collar on fireplace or
rigid vent system. Measure between wall or vent cap extension
and outside mounting plate.
See
Figures 54 and 55
.
Summary of Contents for MILLIVOLT STANDING PILOT DVX36FP31L-4
Page 52: ...39357 0 1018 Page 52 LOG PLACEMENT 12 Place Log I on the two left pins of Log B as shown below...
Page 54: ...39357 0 1018 Page 54 LOG PLACEMENT 14 Place Log K on far right pin of Log B as shown below...
Page 57: ...39357 0 1018 Page 57 LOG PLACEMENT 17 The log assembly is now complete...