background image

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly  

could result in serious injury, death or 

property damage.

—  Do not store or use gasoline or other flam

-

mable vapors and liquids in the vicinity of 

this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Leave the building immediately.

•  Immediately  call  your  gas  supplier 

from a neighbor’s phone. Follow the 

gas supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fire department.

— Installation and service must be per-

formed  by  a  qualified  installer,  service 

agency or the gas supplier.

NOTE:

 Barrier required, but may be sold separately.

 �

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

INSTALLER: 

Leave this manual with the appliance.

CONSUMER: 

Retain this manual for future reference.

This appliance may be installed in 

an aftermarket, permanently located, 

manufactured home (USA only) or mobile 

home, where not prohibited by state or local 

codes.
This appliance is only for use with the type 

of gas indicated on the rating plate. This 

appliance is not convertible for use with other 

gases, unless a certified kit is used.

WARNING

If not installed, operated and maintained in 

accordance with the manufacturer’s instruc-

tions, this product could expose you to sub-

stances in fuel or from fuel combustion which 

can cause death or serious illness.

LUXURY DIRECT VENT 

GAS ZERO CLEARANCE 

FIREPLACE HEATER

 

MILLIVOLT STANDING PILOT

 

DVX36FP31L(N,P)-4

 DVX42FP31L(N,P)-4
 

INTERMITTENT PILOT

 

DVX36FP71L(N,P)-3

 DVX42FP71L(N,P)-3
 

REMOTE CONTROL 

 

DVX36FP91L(N,P)-3

 DVX42FP91L(N,P)-3

GAS-FIRED

UL FILE NO. 

MH30033

Page 1

Summary of Contents for MILLIVOLT STANDING PILOT DVX36FP31L-4

































































































Reviews: