background image

Page 1

DIRECT VENT ZERO CLEARANCE GAS 

FIREPLACE HEATER SERIES

MILLIVOLT (MV)

DVCP(32,36,42)BP3(0,2)(N,P)-2

INTERMITTENT PILOT (IP)

DVCP(32,36,42)BP7(0,2)(N,P)-2

GAS-FIRED

UL FILE NO. MH30033

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

This appliance may be installed in 

an aftermarket, permanently located, 

manufactured home (USA only) or mobile 

home, where not prohibited by state or 

local codes.
This appliance is only for use with the type 

of gas indicated on the rating plate. This 

appliance is not convertible for use with 

other gases, unless a certified kit is used.

 

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death or 

property damage.

—  Do not store or use gasoline or other flam

-

mable vapors and liquids in the vicinity of 

this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow the 

gas supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fire department.

— Installation and service must be per-

formed  by  a  qualified  installer,  service 

agency or the gas supplier.

INSTALLER: Leave this manual with the 

appliance.

CONSUMER: Retain this manual for future 

reference.

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.

 

WARNING

If not installed, operated and maintained 

in accordance with the manufacturer’s 

instructions, this product could expose 

you to substances in fuel or from fuel 

combustion which can cause death or 

serious illness.

Summary of Contents for DVCC32BP30N-2

























































Reviews: