Emerson Rosemount Smart Wireless THUM Reference Manual Download Page 49

Page: 49 / 60

Reference Manual

00809-0100-4075, Rev BA
October 2010

A-5

Smart Wireless THUM Adapter

ORDERING INFORMATION

ACCESSORIES AND SPARE PARTS

Table A-1.

Smart Wireless THUM Adapter Ordering Information

★

The Standard offering represents the most common options. The starred options (

★

) should be selected for best delivery.

The Expanded offering is subject to additional delivery lead time.

Model

Product Description

775

Smart Wireless THUM Adapter

Output

Wireless

Housing

Standard

Aluminum

★

Expanded

SST

Mounting Connection

Standard

- 14 NPT

★

M20-Conduit Adapter

★

PlantWeb Functionality

Standard

HART

Data

★

Certification

Standard

No Approval

★

FM Intrinsically Safe, Non-incendive

★

CSA Intrinsically Safe

★

ATEX Intrinsic Safety

★

ATEX Type n

★

IECEx Intrinsic Safety

★

IECEx Type n

★

INMETRO Intrinsic Safety

★

INMETRO Type n

★

China Intrinsic Safety

★

Korea (KOSHA) Intrinsic Safety

★

India (CCOE) Intrinsic Safety

★

GOST (Russia) Intrinsically Safe

★

Wireless Update Rate, Operating Frequency, and Protocol

Standard

WA3

User Configurable Update Rate, 2.4 GHz DSSS, WirelessHART

★

Omnidirectional, Wireless Antenna, and SmartPower

™

Options

Standard

WK9

Long range, Integral Antenna, Power Scavenging

★

Typical Model Number: 775XD11I5WA3WK9

Table A-2. Accessories

Item Description

Part Number

Remote Mount Kit - AI

00775-9000-0001

Remote Mount Kit - SST

00775-9000-0011

M20-Conduit Adapter

00775-9001-0001

Summary of Contents for Rosemount Smart Wireless THUM





























































Search results

Summary of Contents for Rosemount Smart Wireless THUM

Reviews:

Related manuals for Rosemount Smart Wireless THUM

Brands by name

Popular brands

Emerson Rosemount Smart Wireless THUM, Reference Manual

Search results

Summary of Contents for Rosemount Smart Wireless THUM

Reviews:

Related manuals for Rosemount Smart Wireless THUM

Brands by name

Popular brands