Emerson Rosemount Smart Wireless THUM Reference Manual Download Page 19 | Manualshive

Page: 19 / 60

background image

Reference Manual

00809-0100-4075, Rev BA
October 2010

3-1

Smart Wireless THUM Adapter

Section 3

Mounting

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-2
Loop Current Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-14

SAFETY MESSAGES

Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.

Warnings

Failure to follow these installation guidelines could result in death or serious injury

:

•

Only qualified personnel should perform the installation

Explosions could result in death or serious injury.

•

Before connecting a Field Communicator in an explosive atmosphere, make
sure that the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices

•

Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications

Electrical shock could cause death or serious injury.

•

Use extreme caution when making contact with the leads and terminals

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions: This device may not cause harmful interference. This device must
accept any interference received, including interference that may cause undesired
operation.

This device must be installed to ensure a minimum antenna separation distance of 20
cm from all persons.

«
...
17
18
19
20
21
...
»

Summary of Contents for Rosemount Smart Wireless THUM





























































Reviews:

No comments

Related manuals for Rosemount Smart Wireless THUM

Brand: Patton electronics Pages: 6

Brand: AmazonBasics Pages: 52

ZyXEL ZyAIR 100

Brand: ZyXEL Communications Pages: 10

Brand: Accutone Pages: 8

Brand: Renesas Pages: 26

Brand: Amped Wireless Pages: 2

Brand: Velleman Pages: 18

Brand: BeachTek Pages: 2

Brand: Digitus Pages: 30

Brand: Cisco Pages: 57

Brand: Cisco Pages: 37

Brand: Cisco Pages: 96

Brand: Cisco Pages: 64

Brand: Cisco Pages: 18

Brand: Cisco Pages: 28

Brand: Cisco Pages: 49

Brand: Cisco Pages: 48

Brand: Cisco Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands