Emerson Rosemount Smart Wireless THUM Reference Manual Download Page 3 | Manualshive

Page: 3 / 60

background image

Reference Manual

00809-0100-4075, Rev BA
October 2010

Smart Wireless THUM Adapter

Smart Wireless THUM™ Adapter

Smart Wireless THUM™ Adapter Hardware Revision

1

HART

®

Device Revision

1

Field Communicator Field Device Revision

Dev v2.5 DD v4

NOTICE

Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure to thoroughly understand the contents before
installing, using, or maintaining this product.

The United States has two toll-free assistance numbers and one international number.

Customer Central

1 800 999 9307 (7:00 a.m. to 7:00 p.m. CST)

National Response Center

1 800 654 7768 (24 hours a day)
Equipment service needs

International

1 952 906 8888

The products described in this document are NOT designed for nuclear-qualified
applications.

Using non-nuclear qualified products in applications that require nuclear-qualified hardware
or products may cause inaccurate readings.

For information on Rosemount nuclear-qualified products, contact an Emerson Process
Management Sales Representative.

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please review
the Product Certifications section for any restrictions associated with a safe installation.

•

Before connecting a Field Communicator in an explosive atmosphere, ensure the
instruments are installed in accordance with intrinsically safe or non-incendive field
wiring practices.

Electrical shock can result in death or serious injury:

•

Avoid contact with the leads and terminals. High voltage that may be present on
leads can cause electrical shock.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions. This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operation.

This device must be installed to ensure a minimum antenna separation distance of 20 cm
from all persons.

«
1
2
3
4
5
...
»

Summary of Contents for Rosemount Smart Wireless THUM





























































Reviews:

No comments

Related manuals for Rosemount Smart Wireless THUM

Brand: 1320 Electronics LLC Pages: 5

3CRWE62092B - 11Mbps Wireless LAN PC Card

Brand: 3Com Pages: 16

OfficeConnect 3CRWE254G72

Brand: 3Com Pages: 1

Brand: Rainforest Automation Pages: 29

Universal 70W Power Adapter

Brand: Targus Pages: 2

Brand: EtherWAN Pages: 21

Limetree Bridge

Brand: Lindemann Pages: 40

Brand: S2Konnect Pages: 26

Brand: PureLink Pages: 16

Brand: Dantel Pages: 48

Brand: Pace Pages: 15

Brand: YOKOGAWA Pages: 2

Brand: NetComm Pages: 32

Brand: Conceptronic Pages: 11

Brand: Plantronics Pages: 12

AirLive HP-3000E

Brand: Air Live Pages: 39

Brand: Edimax Pages: 1

Brand: Danfoss Pages: 166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands