Emerson Rosemount Smart Wireless THUM Reference Manual Download Page 4 | Manualshive

Page: 4 / 60

background image

Reference Manual

00809-0100-4075, Rev BA

October 2010

Smart Wireless THUM Adapter

NOTICE

The THUM and all other wireless devices should be installed only after the Smart Wireless
Gateway has been installed and is functioning properly. Wireless devices should also be
powered up in order of proximity from the Smart Wireless Gateway, beginning with the
closest. This will result in a simpler and faster network installation.

NOTICE

During normal operation, or in fault condition, the THUM will cause a 2.5 V drop in the
connected loop. It is important to ensure that the power supply can provide at least 2.5 V
more than the lift off voltage of the wired device to make sure it works properly with the
THUM installed. To determine the lift off voltage for the wired device, review the wired
device operation and installation manual.

«
...
2
3
4
5
6
...
»

Summary of Contents for Rosemount Smart Wireless THUM





























































Reviews:

No comments

Related manuals for Rosemount Smart Wireless THUM

Brand: CoolGear Pages: 19

Redbooks ServeRAID-8s

Brand: IBM Pages: 58

Brand: PATONA Pages: 14

POCKET ETHERNET ADAPTER III

Brand: Xircom Pages: 93

Brand: NEC Pages: 7

Brand: Mesa Pages: 3

Brand: Accutone Pages: 8

Brand: DeLOCK Pages: 4

DMXpro LP510-001

Brand: Synapse Pages: 21

Brand: Hawg Wired Pages: 10

Brand: TP-Link Pages: 37

Brand: AccuPower Pages: 9

Brand: Prudent Way Pages: 6

Brand: Contel Electronics Technology Pages: 4

FriendlyNET Wireless USB Adapter

Brand: Asante Pages: 17

FoneMate SFA-0001

Brand: TeleVue Pages: 2

Brand: Telex Pages: 136

Brand: Daikin Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands