Emerson Rosemount Clarity II T56 Reference Manual Download Page 52

Page: 52 / 60

6. Insert the replacement board in the sensor and push the socket on the replacement

board into the mating pins in the sensor.

CAUTION

Equipment damage

Keep wires pushed away from lamp board when replacing the flange.

A. Wires and flange

B. Mating pins

7. Place the dessicant package in the sensor body.
8. Orient the flange so that the screw holes line up with the holes in the sensor body.

Push the flange back on the sensor body and replace the screws.
Don't let wires push on lamp board. You may need to turn the flange a small
amount until the holes line up.

9. Place the sensor in the calibration cup and reconnect the cable.

10. Calibrate the sensor using either slope or standard calibration.

See

Calibrate slope

Calibrate against a standard

. Do not use grab calibration.

Failure to calibrate the sensor may reduce the life of the sensor.

Maintenance

Reference Manual

July 2020

00809-0100-3565

Emerson.com/Rosemount

Summary of Contents for Rosemount Clarity II T56





























































Search results

Summary of Contents for Rosemount Clarity II T56

Reviews:

Related manuals for Rosemount Clarity II T56

Brands by name

Popular brands

Emerson Rosemount Clarity II T56, Reference Manual

Search results

Summary of Contents for Rosemount Clarity II T56

Reviews:

Related manuals for Rosemount Clarity II T56

Brands by name

Popular brands