Emerson Rosemount 753R Reference Manual Download Page 57

Page: 57 / 60

Reference Manual

00809-0100-4379, Rev AA

March 2006

Rosemount 753R Indicator

www.rosemount.com

Appendix B

Product Certifications

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B-1

Approved Manufacturing Locations . . . . . . . . . . . . . . . . . page B-1

Telecommunication Compliance . . . . . . . . . . . . . . . . . . . . page B-1

Ordinary Locations Certifications . . . . . . . . . . . . . . . . . . . page B-1

Hazardous Locations Certifications . . . . . . . . . . . . . . . . . page B-1

OVERVIEW

This section contains intrinsic safety approval and standard compliance

information for the Rosemount 753R monitor.

APPROVED

MANUFACTURING

LOCATIONS

Rosemount Inc. — Chanhassen, Minnesota, USA

TELECOMMUNICATION

COMPLIANCE

FCC ID: IHDT56DB1 is contained within.

Industry Canada ID: IC ID: 109O-DB1 is contained within.

ORDINARY LOCATIONS

CERTIFICATIONS

As standard, the wireless indicator has been examined and tested to

determine that the design meets basic electrical, mechanical, and fire

protection requirements by FM, a nationally recognized testing laboratory

(NRTL) as accredited by the Federal Occupational Safety and Health

Administration (OSHA).

HAZARDOUS

LOCATIONS

CERTIFICATIONS
North American

Certifications

Factory Mutual (FM) Approvals

N5 FM Class I, Division 2 (Non-incendive)

Certificate Number: 3023264

Nonincendive for Class I, Division 2, Groups A, B, C, and D

Temperature Class T5 Ta = 70° C

Indoor Hazardous (Classified) Locations

WARNING

Substitution of components may impair suitability for Division 2.

Explosion hazard. Do not disconnect equipment when a flammable or

combustible atmosphere is present.

Explosion hazard. Do not open enclosure or replace battery when flammable

or combustible atmosphere is present.

Summary of Contents for Rosemount 753R





























































Search results

Summary of Contents for Rosemount 753R

Reviews:

Brands by name

Popular brands

Emerson Rosemount 753R, Reference Manual

Search results

Summary of Contents for Rosemount 753R

Reviews:

Brands by name

Popular brands