manualshive.com logo in svg

Emerson Rosemount 753R, Reference Manual

Share
Download
Emerson Rosemount 753R Reference Manual Download Page 15

Reference Manual 

00809-0100-4379, Rev AA

March 2006

2-5

Rosemount 753R Indicator

LCD Meter Rotation

In addition to housing rotation, the optional LCD meter can be rotated in 

90-degree increments. To rotate the LCD meter, remove the front housing 

cover (this may require a wrench). Squeeze the two tabs located on the sides 

of the LCD meter and lift the meter out. Rotate the LCD meter to the desired 

direction and snap back into place. Replace the front housing cover and 

tighten.
NOTE

The jumpers may come loose while removing the LCD meter. Be sure that 

they are fully seated in the housing before snapping the LCD meter into place.

Consider RPS 

Positioning

When installing the optional Remote Power Supply (RPS), position the solar 

panel so that it has the best possible access to sunlight throughout the day. If 

direct sunlight access is not available, indirect (reflected) sunlight sources can 

be used.

Summary of Contents for Rosemount 753R





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands