Emerson numatics g3 series Technical Manual Download Page 55

Page: 55 / 71

Series

PROFIBUS

‐

Technical

Manual

Page

TDG3PTTM1-2EN

02/09

Subject to change without notice

www.numatics.com/g3

Bit Mapping Rules

The bit mapping for a G3 manifold varies with the physical configuration of the manifold. The following is a
breakdown of the bit mapping rules associated with the Numatics valve manifold.

Valve Side

Solenoid coil outputs are connected to the valve coils using the Z-Boards

™

The valve solenoid coil output portion of the total output size is adjustable from 0 to 4 bytes.

Solenoid coil output addressing begins at the 1

manifold station nearest the node using “14” coil 1

and

then, if applicable, the “12” coil, and continues in ascending order away from the communication node.

Each manifold station allocates 1 or 2 output bits. This is dependent on the Z-Board

™

type installed.

A single Z-Board

™

allocates 1 output bit. A double Z-Board

™

allocates 2 output bits.

Z-Boards

™

can be used in any arrangement (all singles, all doubles, or any combination) as long as output

group No. 1 and output group No. 2 bits do not overlap (i.e. combinations of Z-Boards

™

could exist where

the physical configuration of the manifold could exceed the output capacity.

Discrete I/O Side

Outputs

The Sub-Bus output byte size portion is self-configuring in byte increments, after an output module is
installed on the Sub-Bus and power is applied.

Outputs are mapped consecutively by module. The output bits from the 1

module will be mapped directly

after the bits from the valve coils. The output bits from the second module will be mapped directly after
the output bits from the 1

module and so on.

Inputs

The Sub-Bus input byte size portion is self-configuring in byte increments, after an input module is
plugged into back plane and power is applied.

Inputs are mapped consecutively by module. The input bits from the 1

module will be mapped at byte 0.

The input bits from the second module will be mapped directly after the input bits from the 1

module and

so on.

Single solenoid valves can be used with double

Z-Boards

. However,

one of the two available outputs will remain unused.

NOTE!

Summary of Contents for numatics g3 series








































































Search results

Summary of Contents for numatics g3 series

Reviews:

Related manuals for numatics g3 series

Brands by name

Popular brands

Emerson numatics g3 series, Technical Manual

Search results

Summary of Contents for numatics g3 series

Reviews:

Related manuals for numatics g3 series

Brands by name

Popular brands