Emerson Liebert APM 120 Manual Download Page 48

Page: 48 / 144

Parallel System and LBS System Installation

Liebert

APM

™

4.0

ARALLEL

YSTEM

AND

LBS S

YSTEM

NSTALLATION

This chapter gives details on the installation of a parallel system and an LBS system.

4.1

General

A parallel Liebert APM system can consist of two Liebert APM cabinets connected in parallel without

a main system static bypass. Instead, the bypass static switches of each UPS share the load when the

system transfers to the utility bypass supply. A third-party APM paralleling switchboard may be used

to provide external maintenance capability. See

Figure 23

for details.

From a power viewpoint, each module is internally identical to the single-module configuration. A

parallel system requires intermodule control signals to manage the load sharing, synchronizing and

bypass switching. The control signals are connected through parallel communication cables, which

provide bi-directional communication between the two Liebert APM units of the system. A second

parallel cable is provided to establish redundancy.
When Liebert APM units are to be connected in parallel, a sharing inductor assembly is required and

must be installed inside the Liebert APM cabinet. The inductor may be installed at the factory or

field-installed.

4.2

System Installation Procedures

The installation of a parallel UPS should follow the procedures for a single UPS module with the

additional requirements detailed in this section.

4.2.1 Preliminary Checks

Be sure that the options of the parallel cables are correct and that the modules are of the same rating,

model and with the same software and hardware release.

4.2.2 Cabinet Installation

Position the UPS modules and make connections as shown in

Figure 23

. The output distribution

consisting of external UPS output switches and maintenance bypass must be installed, as shown in

Figure 23

, to facilitate maintenance and system testing.

WARNING

To achieve coordinated operation of the modules in the parallel system, it is required to

configure each module separately using Emerson configuration software. This must be done

by Emerson service personnel.

Summary of Contents for Liebert APM 120

















































































































































Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands

Emerson Liebert APM 120, Manual

Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands