Emerson Liebert APM 120 Manual Download Page 89

Page: 89 / 144

Liebert IntelliSlot

Installation

Liebert

APM

™

8.2.1 Liebert IntelliSlot

Unity Cards—IS-UNITY-LIFE, IS-UNITY-S, IS-UNITY-DP

•

IS-UNITY-LIF

E (Included): Offers a web interface to manage and configure the Emerson

Life.net and Emerson proprietary protocols for use with the Emerson Life Station

™

, Liebert

Nform

and Emerson

Trellis

™

•

IS-UNITY-DP

: Offers a web interface to monitor and configure the Life.net and Emerson

Network Power proprietary protocols for use with the Emerson Life Station, Liebert Nform and

Emerson Trellis. It allows selection and configuration of two of the available third-party

protocols—SNMP, Modbus or BACnet—for operation with building management systems.

•

Liebert IntelliSlot

Dry Contact Card (IS-RELAY)

: Provides dry contact alarm information,

including: On Battery, On Bypass, Low Battery, Summary Alarm, UPS Fault and On UPS signals

for communication to a remote monitoring system or for use with Liebert MultiLink

software.

•

Liebert IntelliSlot MultiPort Card (IS-MULTIPORT)

Provides dry contact alarm

information, including: On Battery, Low Battery signals for communication to four servers for use

with Liebert MultiLink software.

•

IS-485EXI

: The Liebert IntelliSlot 485 EXI Card provides connection to a Liebert SiteLink-E™

allowing Liebert SiteScan® Web 4.0 monitoring and control of your Liebert equipment.

8.3

Liebert IntelliSlot Card Web Interface

The IS-Unity-Life and IS-Unity-DP IntelliSlot cards offer a Web interface, yielding a wide variety of

status and summary information through an Ethernet connection. Liebert’s IS-Unity-DP also

provides e-mail and text notification.

Figure 62 Liebert IntelliSlot Web card display

Summary of Contents for Liebert APM 120

















































































































































Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands

Emerson Liebert APM 120, Manual

Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands