Emerson Liebert APM 120 Manual Download Page 91

Page: 91 / 144

Liebert IntelliSlot

Installation

Liebert

APM

™

8.4.2 Liebert IntelliSlot

Relay Card Jumper Setup

The Liebert IntelliSlot Relay Card has five jumpers, P3 through P7, as shown in

Figure 64

. Each

jumper connects two pins.

Figure 64 Jumper location and numbering

By default all five jumpers have shunts installed. The two pins are shunted together to provide the

functions shown in

Table 21

, allowing relay commons to be tied together.

The jumpers should be removed if there is any external voltage source that may intentionally or

inadvertently be connected to the relay.
Removing the shunt from any two pins breaks the connection between the relay commons so they are

not tied together.

Table 21 Jumper connections

Jumper

Relay

On Battery

UPS Fault

Low Battery

On Bypass

Summary Alarm

NOTE

Refer to the Liebert IntelliSlot Relay Card manual, SL-23211 for additional details. the

document is available at the Liebert Web site,

www.liebert.com

Jumper

Front

Card

Summary of Contents for Liebert APM 120

















































































































































Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands

Emerson Liebert APM 120, Manual

Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands