Emerson AMS Installation Manual Download Page 66 | Manualshive

Page: 66 / 92

Emerson AMS Installation Manual Download Page 66

3. Hook the CHARM Address Terminal Block into the lower part of the address slot, the

right-most slot (see

), and gently push it in.

The CHARM Address Terminal Block locks with an audible click.

4. Ensure that the latch of the Address Terminal Block is in the open position as shown

. If the latch is in the closed position, use a suitable flat-tip screwdriver

to open it.

a) Insert the screwdriver into the latch.

b) Move the screwdriver down to switch the latch to the open position.

c) Remove the screwdriver.

5. Gently push the Address Plug into the CHARM Address Terminal Block installed

before. The Address Plug locks with an audible click – the latch of the Address
Terminal Block flips in the close position.
The Address Plug only fits in one direction.
Install Address Plug 1 on the first AMS Asset Monitor, Address Plug 2 on the second
AMS Asset Monitor, Address Plug 3 on the third AMS Asset Monitor, and so forth
(supported with a later release, see

Network connection

Figure 5-16: Address Plug installation

A. CHARM Address Terminal Block

B. Address Plug

C. Latch in open position

6. Continue with the installation or close the door (

Close the AMS Asset Monitor

5.9

Label the installed CHARMs

The CHARM labeling component consists of a label support that holds a label and its
protective plastic cover. Remove the label support from the AMS Asset Monitor before
writing or typing the CHARM IDs on the label.

Installing CHARMs hardware

Installation Guide

April 2020

MHM-97923-PBF

66

MHM-97923-PBF, Rev. 1.0

«
...
64
65
66
67
68
...
»

Summary of Contents for AMS





























































































Reviews:

No comments