manualshive.com logo in svg

Emerson AMS, Installation Manual, Page: 10 / 92

Share
Download
Emerson AMS Installation Manual Download Page 10

Table 1-3: Product type and ordering numbers of AMS Asset Monitor and compatible
DeltaV hardware

 (continued)

Hardware

Product type number

Ordering number

Thermocouple/mV input
CHARM

KL3032X1-BA1

SE4303T02-RS

AI 4 to 20 mA CHARM

KL3021X1-BA1

SE4303T01-RS

DI 24 V DC Low-Side Sens (dry
contact) CHARM

KL3003X1-BA1

SE4301T02-RS

DO 24 V DC High-Side CHARM

KL3002X1-BA1

SE4302T01-RS

Standard Terminal Block

KL4502X1-BA1

SE4501-RS

Thermocouple/mV Terminal
Block

KL4502X1-NA1

SE4504-RS

Relay Output Terminal Block

KL4502X1-MA1

SE4503-RS

Address Terminal Screw Block

KL4502X1-DA1

KL4502X1-DA1-RS

Address Terminal Plug #1

KL4501X1-BA1

KL4501X1-BA1-RS

CHARM labeling component

KL4502X1-VA1

KL4502X1-VA1-RS

Replacement label for labeling
component

---

SE4606T02-RS

1.2

Symbols

Note

This symbol marks passages that contain important information.

 CAUTION

This symbol marks operations that can lead to malfunctions or faulty measurements, but
will not damage the device.

 DANGER

A danger indicates actions that can lead to property damage or personal injury.

According to IEC 61010, this symbol means that the documentation of the
device must completely be read and understood before installing and
commissioning of the device. Observe all safety related instructions in this
document.

Warning, electric shock hazard.

General

Installation Guide

April 2020

MHM-97923-PBF

10

MHM-97923-PBF, Rev. 1.0

Summary of Contents for AMS





























































































Reviews:

No comments