Emerson AMS Installation Manual Download Page 52

Page: 52 / 92

5.2.1

Connect the sensor wiring

Figure 5-7: Sensor connection

A. VI Piezo CHARM

B. CHARM Baseplate

C. CHARM Terminal Block

D. 2-wire piezoelectric sensor

E. Cable shield connection
F. Top view of the sensor connector – terminal A

G. Top view of the sensor connector – terminal B

Prerequisites

•

Wire cutter

•

Tool for removing the cable sheath

•

Wire stripper

•

Suitable screw driver for the CHARM Terminal Block screws

•

Shielded sensor cable

•

Observe the hints in

Wiring guidelines

Procedure

1. At opened door, lead the sensor cable through a cable gland close to the slot where

the CHARM to be connected is installed.

2. Strip the cable sheath at a length of approximately 200 mm.
3. Strip each wire at a length of approximately 10 mm.
4. Connect the wires to the CHARM Terminal Block.

Installing CHARMs hardware

Installation Guide

April 2020

MHM-97923-PBF

MHM-97923-PBF, Rev. 1.0

Summary of Contents for AMS





























































































Search results

Summary of Contents for AMS

Reviews:

Related manuals for AMS

Brands by name

Popular brands

Emerson AMS, Installation Manual

Search results

Summary of Contents for AMS

Reviews:

Related manuals for AMS

Brands by name

Popular brands