Emerson AMS Installation Manual Download Page 46

Page: 46 / 92

2. Connect a further Ethernet cable to the other RJ-45 socket and connect this cable to

one RJ-45 socket of the 100 Mbit/s switch of the second AMS Asset Monitor.

3. Continue connecting AMS Asset Monitor as described in

Step 2

until all AMS Asset

Monitors are part of the DCN.

Connect AMS Asset Monitor in a star network

Figure 4-20: RJ-45 sockets

A. RJ-45 sockets of the 100 Mbit/s Ethernet switch

Procedure

1. Connect the Area Controlled Network (ACN) to the Ethernet switch.
2. Connect one RJ-45 socket of the 100 Mbit/s switch of the AMS Asset Monitor to the

Ethernet switch.

3. Continue with

Step 2

until all AMS Asset Monitors are connected to the Ethernet

switch.

Connect AMS Asset Monitor in a hybrid network

Procedure

1. Connect the AMS Asset Monitors to be daisy-chained as described in

Connect AMS

Asset Monitor in a daisy-chained network

2. Connect the remaining AMS Asset Monitors to the Ethernet switch as described in

Connect AMS Asset Monitor in a star network

Installing AMS Asset Monitor hardware

Installation Guide

April 2020

MHM-97923-PBF

MHM-97923-PBF, Rev. 1.0

Summary of Contents for AMS





























































































Search results

Summary of Contents for AMS

Reviews:

Related manuals for AMS

Brands by name

Popular brands

Emerson AMS, Installation Manual

Search results

Summary of Contents for AMS

Reviews:

Related manuals for AMS

Brands by name

Popular brands