Emerson AMS Installation Manual Download Page 12 | Manualshive

Page: 12 / 92

background image

Note

If the equipment has been exposed to a hazardous substance, a Material Safety Data Sheet
(MSDS) must be included with the returned materials. An MSDS is required by law to be
available to people exposed to specific hazardous substances.

1.6

Storage and transport

Store and transport the device only in its original packaging. Technical data specifies the
environmental conditions for storage and support.

1.7

Disposal of the device

Provided that no repurchase or disposal agreement exists, recycle the following
components at appropriate facilities:

•

Recyclable metal

•

Plastic elements

Sort the remaining components for disposal, based on their condition. National laws or
provisions on waste disposal and protection of the environment apply.

Note

Environmental hazards! Electrical waste and electronic components are subject to
treatment as special waste and may only be disposed by approved specialized companies.

1.8

China RoHS Compliance

Our products manufactured later than June 30, 2016 and those which are sold in the
People's Republic of China are marked with one of the following two logos to indicate the
Environmental Friendly Use Period in which it can be used safely under normal operating
conditions.

Products without below mentioned marking are either manufactured before June 30 or
are non-electrical equipment products (EEP).

Circling arrow symbol with "e": The product contains no hazardous substances over
the Maximum Concentration Value and it has an indefinite Environmental Friendly
Use Period.

Circling arrow symbol with a number: This product contains certain hazardous
substances over the Maximum Concentration Value and it can be used safely under
normal operating conditions for the number of years indicated in the symbol. The
names and contents of hazardous substances can be found in the folder "China
RoHS Compliance Certificates" on the documentation CD or DVD enclosed with the
product.

General

Installation Guide

April 2020

MHM-97923-PBF

12

MHM-97923-PBF, Rev. 1.0

«
...
10
11
12
13
14
...
»

Summary of Contents for AMS





























































































Reviews:

No comments

Related manuals for AMS

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: Eagle Eye Pages: 3

Brand: VALTRONICS Pages: 13

Brand: JIANGSU Pages: 8

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Brand: OHAUS Pages: 2

Brand: A&D Pages: 68

FLEXFLO M4 Series

Brand: Blue-White Pages: 64

Brand: Dewetron Pages: 24

Brand: Chroma Pages: 63

Ranger TDR VDV501-090

Brand: Klein Tools Pages: 44

Brand: PRONIVO Pages: 40

Brand: socomec Pages: 34

MarMonix MSL-765

Brand: Farnell Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands