Emerson AMS Installation Manual Download Page 45

Page: 45 / 92

Figure 4-18: Network topology – hybrid

A. First RJ 45 socket of the Ethernet switch (ACN/LAN)

B. Second RJ 45 socket of the Ethernet switch (ACN/LAN)

C. RJ 45 socket for connection to WAN for configuration of the AMS Asset Monitor and

connection to subsequent systems such as Plantweb Optics

D. Optional connection, if no connection between switch and ACN

E. Connection to an Area Controlled Network (ACN)
F. Switch

Connect AMS Asset Monitor in a daisy-chained network

Figure 4-19: RJ-45 sockets

A. RJ-45 sockets of the 100 Mbit/s Ethernet switch

Procedure

1. Connect the Area Controlled Network (ACN) to one RJ-45 socket of the 100 Mbit/s

switch of the first AMS Asset Monitor.

Installation Guide

Installing AMS Asset Monitor hardware

MHM-97923-PBF

April 2020

MHM-97923-PBF, Rev. 1.0

Summary of Contents for AMS





























































































Search results

Summary of Contents for AMS

Reviews:

Related manuals for AMS

Brands by name

Popular brands

Emerson AMS, Installation Manual

Search results

Summary of Contents for AMS

Reviews:

Related manuals for AMS

Brands by name

Popular brands