EMC2 AX100 Series Manual Download Page 68 | Manualshive

Page: 68 / 68

background image

68

AX100-Series - Installing a Fibre Channel Storage System with a Direct Connection to a NetWare Server

Verifying Your Configuration

10. If you caused any virtual disks to fail over, restore the disks to

their original SP:

powermt restore

11. For each HBA connected to the storage system, repeat steps 3

through 10.

What Next?

You have completed the installation for one storage system connected
to one server. If you have another server to connect to the storage
system, start with

Installing HBAs in the Server

(page 6). If you have

another storage system to connect to a server, start with

◆

Unpacking the Storage System

(page 16) for a

new

AX100SC storage

system

◆

Installing the UPS (AX100 Only)

for a

new

AX100 storage

system

◆

Connecting the Storage System to the Server

(page 49) for an

existing

storage system

Copyright © 2004-2005 EMC Corporation. All Rights Reserved.

EMC believes the information in this publication is accurate as of its publication date. The information is subject to
change without notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED "AS IS." EMC CORPORATION MAKES NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS
PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.

Use, copying, and distribution of any EMC software described in this publication requires an applicable software
license.

Trademark Information

EMC

2

, EMC, CLARiiON, Navisphere, and PowerPath are registered trademarks and Access Logix, FLARE, MirrorView, SAN Copy, and SnapView are

trademarks of EMC Corporation.
All other trademarks mentioned herein are the property of their respective owners.

«
...
66
67
68

Summary of Contents for AX100 Series





































































Reviews:

No comments

Related manuals for AX100 Series

Brand: u-blox Pages: 2

Brand: Digital Equipment Pages: 98

MYC-C8MMQ6-8E2D-160-I

Brand: MYiR Pages: 50

Brand: MACHINIST Pages: 15

Brand: Gigabyte Pages: 93

Brand: QDI Pages: 23

Brand: MSI Pages: 186

Brand: J&W Pages: 36

Brand: Freescale Semiconductor Pages: 4

Brand: Icop Pages: 40

7001G - VIA Mini ITX Motherboard

Brand: VIA Technologies Pages: 76

MAG Z490 TOMAHAWK

Brand: MSI Pages: 76

VIOTECH 3100 PLUS - BIOS

Brand: Biostar Pages: 41

Brand: Acorp Pages: 66

Brand: Sanela Pages: 30

970A-G46 Series

Brand: MSI Pages: 78

Brand: Biostar Pages: 32

Brand: Systium Technologies Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands